Publicité
Información general
Partes incluidas en el juego
Artículo
1
2
3
4
5
6
7
1) Frame Assembly: QTY 1
8
2) Bottom Duct Assembly: QTY 1
1
1
2) Bottom Duct Assembly: QTY 1
2
3) Mouting Bracket: QTY 2
4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)
6
2
4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)
8
S
S
1) Frame Assembly: QTY 1
Nombre de la parte
Conjunto del marco
Conjunto del ducto inferior
Soporte de montaje
Tornillo A :1-3/16" de largo
Tornillo B: 1-3/4" de largo
Decoración lateral (Sólo superficie
de montaje)
Plantilla para montaje en superficie
Plantilla para montaje al ras
3) Mouting Bracket: QTY 2
3
5
7
Maximum Cutout Opening Width 28" (711.2 mm)
Minimum Cutout Opening Width 27-3/4" (704.9 mm)
1. Align the Surface Mounting Template center line with the
center of the cabinet. Align the Floor Line with the bottom
of the cabinet at the desired height. Tape it into place.
2. Predrill 4 holes marked A with a ¹ ₁₆" drill bit.
Center Line
3. Cut the cabinet opening between the minimum and
BUILT-IN TRIM KIT
maximum cutout opening lines. Be careful to cut precisely
SURFACE MOUNTING TEMPLATE
along the Floor Line of the cutout.
4. Remove template from the cabinet.
FOR DESIGNER SERIES MICROWAVE OVEN
14-1/4" (361.95 mm)
14" (355.6 mm)
1/4"
(6.2 mm)
Floor Line of Cutout Opening
CABINET CUTOUT LINE
Cutout Opening Width 29-5/8" (752.5 mm)
CABINET CUTOUT LINE
CABINET CUTOUT LINE
Edges to align Side Spacer Templates (R and L)
BUILT-IN TRIM KIT
FLUSH MOUNTING TEMPLATE
FOR DESIGNER SERIES MICROWAVE OVEN
Side Spacer - L
Side Spacer - R
1. Align the Flush Mounting Template center line with the center of the
cabinet. Align the Floor Line with the bottom of the cabinet at the
desired height. Tape it in place.
13/16" Min.
2. Cut the cabinet opening along the three Cabinet Cutout Lines and
15/16 Max.
FIGURE 1
the Floor Line.
Side Spacer (2 required)
Must protrude from edge of cabinet
3. Install two Side Spacers (see FIGURE 1) and one Bottom Spacer (see
1-9/16"
(39.7 mm)
cutout towards center as shown.
Bottom and Side
FIGURE 2) as specified in FIGURE 3. Be sure to offset all three spacers
Spacer (R and L) Offset
by 1⁹ ₁₆" from the front surface of the cabinet.
4. Cut out the Side Spacer Templates (R and L) and align the indicated
24" min. width
Bottom Spacer centered with cabinet cutout
edge to the corresponding Side Spacer (see FIGURE 3). Be careful to
27-7/8" max. width
align the Floor Line to the bottom edges of the Side Spacers.
FIGURE 3
5. Predrill two holes indicated "A" in Side Spacer - R with a ¹ ₁₆" drill bit.
6. Predrill two holes indicated "B" in Side Spacer - L with a ¹ ₁₆" drill bit.
7. Remove template from the cabinet.
FIGURE 2
Bottom Spacer (1 required) ¹ ₄" plywood
1/4" (6.35 mm)
CENTER LINE
14" (355.9 mm)
14-13/16" (376.2 mm)
FLOOR LINE OF CUTOUT OPENING
Abertura del gabinete o pared
Dimensiones de
CANT.
recorte
1
Altura A
1
2
2
4
Ancho B
2
1
Profundidad C
2) Bottom Duct Assembly: QTY 1
1
1
4
4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)
Ubicación del
tomacorriente eléctrico
El tomacorriente NO debe estar en el área
sombreada como se indica en la figura 1.
noTAS:
• Si la dimensión de profundidad (C) es mayor a 21"
1/4"
(53.3 cm), la ubicación del tomacorriente puede
(6.2 mm)
TINSKB180MRR0
estar en cualquier área de la pared posterior.
• El piso de la abertura debe estar construido de
madera laminada lo suficientemente resistente para
soportar el peso del horno y la capacidad de carga
(aproximadamente 100 libras). El piso debe estar
nivelado para una correcta operación del horno.
Asegúrese de verificar el código de construcción
local ya que puede requerir cercar la abertura
1/4" (6.35 mm)
con tabiques laterales, superior y posterior. El
funcionamiento apropiado del horno no requiere
TINSKB181MRR0
del cercado.
20
20
2) Bottom Duct Assembly: QTY 1
Brindas
Superficie
Montaje
Montaje
Mínimo
17-5/16"
16-9/16"
(439.8mm)
(420.7mm)
Máximo
N/A
16-13/16"
(427mm)
29-5/8"
27-3/4"
Mínimo
(752.5mm)
(704.9mm)
Máximo
N/A
28"
(711.2mm)
Mínimo
20"
20"
4) SIDE DECORATION: QTY 2
(503mm)
(503mm)
(SURFACE MOUNTING ONLY)
PRECAUCIÓN
Publicité
