Accessories; Environmental Protection; Technical Data - Metabo WPB 36 LTX BL 230 Mode D'emploi

Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
Remove the battery pack from the machine to
transport the machine.
10. Troubleshooting
The electronic signal indicator (4) lights up and
the load speed decreases. The temperature is too
high! Run the machine in idling until the electronic
signal indicator switches off.
The electronic signal display (4) flashes and
the machine does not start. The restart protection
is active. The machine will not start if the battery
pack is inserted while the machine is on. Switch the
machine off and on again.
The electronic signal display (4) flashes and
the machine does not start. Press the button (5);
the LEDs indicate the charge level. When the
battery pack is empty it must be recharged.
Electronic safety stop: The electronic signal
display (4) flashes and the machine was
SWITCHED OFF automatically. If the slew rate of
the current is too high (for example, if the machine
suddenly seizes or kickback occurs), the machine
switches off. Switch off the machine. Switch it on
again and continue to work as normal. Try to
prevent the machine from seizing. See chapter 3.2.

11. Accessories

Only use original Metabo battery packs and Metabo
accessories.
See page 4.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
See page 4.
A Chargers
B Battery pack
C Grinding wheel (always use with safety guard
attached)
D Lamellar grinding disc (always use with safety
guard attached)
E Parting safety guard.
F Cut-off wheel(always use with parting safety
guard attached)
G Diamond discs (always use with parting safety
guard attached)
H Hand guard (for attaching under the additional
side-mounted handle.)
I Extension piece (for working with supporting
discs. Increases the distance between the
spindle and the supporting disc by approx. 35
mm)
J Supporting disc for fibre discs (always attach
using the supporting disc clamping nut
supplied.) (always use with the hand guard
attached.)
K Fibre discs (always use with the hand guard
attached.)
L Steel wire brushes (always use with the hand
guard attached.)
M Adjusting nut (9)
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to power tools must only be carried
out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs must not be disposed of with regular
waste! Please return faulty or used battery packs to
your Metabo dealer!
Do not throw battery packs into water.

14. Technical Data

Explanatory notes on the specifications on page 2.
Changes due to technological progress reserved.
U = Battery pack voltage
D = max. diameter of accessory
max
t = max. permitted thickness of clamping
max,1
shank on accessory when using clamping
nut (9)
t = grinding wheel/cut-off wheel:
max,3
max. permitted thickness of accessory
M = Spindle thread
l = Length of the sanding spindle
n = No-load speed (maximum speed)
P = Rated input power
1
P = Power output
2
m = Weight (with the smallest battery pack)
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
ENGLISH en
11