Dust Extraction; Cleaning & Maintenance; Accessories; Environmental Protection - Metabo FMS 200 Intec Notice Originale

7. Use
7.1 Switching On and Off
Switching on:
Move switch (3) to "I" position.
Switching off:
Move switch (3) to "O" position.
7.2

Dust Extraction

To optimise the dust extraction performance, fit the
sanding disc such that the holes on the sanding disc
(1) and sanding plate (2) are aligned.
Integrated extraction system:
Install the dust collection box (4) (see illustration,
page 3). To optimise the extraction performance,
empty the dust collection box (4) in good time and
clean the filter (6).
External extraction system:
Fit dust extraction nozzle (see chapter on
Accessories). Connect a suitable extraction device.
Use a suction hose with a 35 mm connector
diameter. See Accessories section.
Note: When sanding abrasive material (e.g. plaster,
etc.) we recommend connecting a suitable dust
extractor.
8. Cleaning, Maintenance
Empty dust collection box (4).
- Open cleaning flap (5).
- Empty dust collection box (4).
- Remove fluted filter (6) and knock off dust stuck to
filter or remove with brush.
- When inserting, ensure that the fluted filter (6) is
inserted in the lateral guides.
Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the
motor.
Replacing worn sanding plate (2)
- Remove fixing screws (on lower side of sanding
plate).
- Take off sanding plate.
- For sanding plate (as replacement), refer to the
Accessories chapter.
- Mount sanding plate.
- Refit fixing screws (on lower side of sanding plate)
and tighten.

9. Accessories

Use only genuine Metabo accessories.
See page 4.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
A Sanding plate (as replacement)
B Dust collection box with fluted filter for multiple
cleaning (as replacement)
C Fluted filter (as replacement)
D Perforated adhesive sanding discs for all types
of wood, 2-piece, 100 x 150 mm
E Perforated adhesive sanding discs for paint,
lacquer, spattle, 2-piece, 100 x 150 mm
F Dust extraction connection
G Metabo universal vacuum cleaner
For complete range of accessories, see
www.metabo.com or the main catalogue.
10. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
The connection cable must only be replaced by
Metabo or an authorised customer service
workshop.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

11. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.

12. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D = Dimensions of sanding plate
P = Nominal power input
1
P = Power output
2
s = orbital frequency at no load
0
s = orbital frequency at nominal load
1
S = Oscillating circuit diameter
Intec = Dust collection box
m = Weight without mains cable
Measured values determined in conformity with
EN 62841.
Machine in protection class II
~
Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
ENGLISH en
9