Publicité
CORDLESS SMALL ANGLE GRINDER
DCG418
Congratulations!
You have chosen a D
WALT tool. Years of experience, thorough
e
product development and innovation make D
most reliable partners for professional power tool users.
Technical Data
Voltage
Type
Battery type
Max. Power output
No‑load/rated speed
Grinding Wheel diameter
Grinding Wheel thickness (max)
Cutting off wheel diameter
Cutting off wheel thickness (max)
Wire wheel diameter
Wire wheel thickness (max)
Spindle diameter
Spindle length
Weight (without battery pack)
Noise values and/or vibration values (triax vector sum) according to EN62841‑2‑3:
L
(emission sound pressure level)
PA
L
(sound power level)
WA
K (uncertainty for the given sound level)
Surface grinding
Vibration emission value a
=
h,AG
Uncertainty K =
Disc sanding
Vibration emission value a
=
h,DS
Uncertainty K =
Concrete grinding
Vibration emission value a
h,CG
Uncertainty K =
Cutting off
Vibration emission value a
h,CO
Uncertainty K =
The vibration and/or noise emission level given in this
information sheet has been measured in accordance with
a standardised test given in EN62841 and may be used to
compare one tool with another. It may be used for a preliminary
assessment of exposure.
WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However
if the tool is used for different applications, with different
accessories or poorly maintained, the vibration and/or
WALT one of the
e
DCG418
V
DC
W
min
‑1
mm
mm
mm
mm
mm
mm
mm
kg
dB(A)
dB(A)
dB(A)
m/s
2
m/s
2
m/s
2
m/s
2
=
m/s
2
m/s
2
=
m/s
2
m/s
2
noise emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration and/
or noise should also take into account the times when the
tool is switched off or when it is running but not actually
doing the job. This may significantly reduce the exposure
level over the total working period.
Identify additional safety measures to protect the
54
operator from the effects of vibration and/or noise such
2
as: maintain the tool and the accessories, keep the
Li‑Ion
hands warm (relevant for vibration), organisation of
work patterns.
2300
WARNING : Grinding thin sheets of metal or other easily
9000
vibrating structures with a large surface can result in a
125
total noise emission much higher (up to 15 dB) than the
6
declared noise emission values. Such workpieces should
125
as far as possible be prevented from emitting sound by
3
suitable measures such as the application of heavy flexible
115
damping mats. The increased noise emission is also to be
considered for both the risk assessment of noise exposure
13
and selecting adequate hearing protection.
M14
EC‑Declaration of Conformity
21.45
2.25
Machinery Directive
85
93
Cordless Small Angle Grinder
3
DCG418
D
WALT declares that these products described under
e
Technical Data are in compliance with:
8.4
2006/42/EC, EN62841‑1:2015 +A11:2022 EN IEC62841‑2‑3:2021
1.5
+A11:2021.
These products also comply with Directive 2014/30/EU and
< 2.5
2011/65/EU. For more information, please contact D
the following address or refer to the back of the manual.
1.5
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of D
6.9
1.5
6.9
Markus Rompel
1.5
Vice President of Engineering, PTE‑Europe
D
WALT, Richard‑Klinger‑Straße 11,
e
65510, Idstein, Germany
20.03.2023
EnGLIsh
WALT at
e
WALT.
e
43
Publicité
