Locking Function - Monacor International JTS US-1000D Mode D'emploi

5.2 Adjusting the reception group and the
transmission channel
1) Keep the key (6) pressed for 2 s until the indica-
tion FREQ (b) starts flashing. Then shortly press
the key once again so that the indication
"GROUP" (c) and the letter "G" of the group indica-
tion (j) start flashing.
Note: To exit the adjusting mode without making an
adjustment, press the key
the display shows
return to normal operation.
2) Use the cursor keys
reception group ( , ,
groups will be scanned in descending order; with
L
the key , they will be scanned in ascending order.
The corresponding channels and transmission fre-
quencies can be found in the table in fig. 4.
3) Confirm the input with the key
"GROUP" (c) and "CH" (k) will start flashing.
4) Use the cursor keys to adjust the transmission
channel (1 – 16): With the key
be scanned in descending order; with the key
they will be scanned in ascending order.
5) To memorize the adjustments for the reception
groups and the transmission channel, press the
key . The display will shortly show
adjusting mode will be exited, and the unit will go to
normal operation.
Group
A
Channel
1 790.875
2 792.625
3 794.250
4 795.625
5 797.125
6 798.875
7 801.125
8 802.250
9 803.625
10 805.250
11 805.750
12 808.625
13 809.125
14 810.000
15 813.250
16 813.750
Fig. 4 Received frequencies in MHz of the groups and channels
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
so many times until
. The unit will then
M L
(4) and (5) to adjust the
or ): With the key
. On the display,
M
, the channels will
B C
790.750 791.125 790.625
791.375 791.750 791.125
793.125 792.625 791.875
794.000 793.750 793.625
795.250 794.500 795.875
796.250 796.125 797.125
796.875 796.875 797.875
798.000 798.250 799.125
798.875 799.000 800.875
800.250 800.875 801.375
803.250 804.500 802.875
804.000 805.875 803.375
805.625 806.625 804.125
806.750 807.750 806.250
808.250 808.375 807.625
813.750 813.750 813.625
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may

5.3 Locking function

With the locking function activated, it is no longer pos-
sible to switch off the receiver and to call the mode for
frequency adjustment or group/channel adjustment. If
this is tried, the indication "LOCK" (a) starts flashing on
the display.
5.3.1 Activating the locking function
1) Keep the key
tion FREQ (b) starts flashing. Then shortly press
the key
"LOCK" (d) starts flashing and
on the display.
M
, the
2) Switch to
3) Confirm the activation with the key
will shortly indicate
be exited, and the unit will change to normal oper -
ation. As a reminder of the activated key lock,
"LOCK" (a) will be indicated.
5.3.2 Deactivating the locking function
1) Keep the key
L
,
switches to
2) Deactivate the key lock with the key
play will switch to
3) Terminate the unlocking process with the key
, the
The display will shortly indicate
mode will be exited, and the unit will change to nor-
mal operation.
6 Specifications
Type of unit: . . . . . . . . . PLL multifrequency receiver
D
Radio frequency range: . 790 – 814 MHz
Frequency stability: . . . . ±0.005 %
Audio frequency range: . 40 – 18 000 Hz
THD: . . . . . . . . . . . . . . . < 0.6 %
Dynamic range: . . . . . . . > 105 dB
Noise suppression: . . . . pilot tone squelch,
Audio outputs
XLR, bal.: . . . . . . . . . 100 mV/150 Ω
6.3 mm jack, unbal.: . 500 mV 1 kΩ
Ambient temperature: . . 0 – 40 °C
Power supply: . . . . . . . . 12 – 18 V /600 mA via the
Dimensions
(w/o antennas): . . . . . . 211 × 40 × 137 mm
Weight: . . . . . . . . . . . . . 1 kg
Subject to technical modification.
®
(6) pressed for 2 s until the indica-
three times again so that the indication
L
with the key (5).
, the adjusting mode will
(6) pressed for 3 s until the display
and "LOCK" (d) starts flashing.
.
with true diversity technique
noise mute
power supply unit supplied
connected to 230 V~/50 Hz
is indicated
. The display
M
(4). The dis-
.
, the adjusting
11