Publicité
Si une meule électrique est utilisée, veiller à ne pas surchauffer les
dents. NE PAS laisser les pointes/dents virer au rouge ou au bleu. NE
PAS plonger la lame dans de l'eau pour la refroidir. Ceci changerait la
trempe du métal, risquant de causer la rupture de la lame.
3. Une fois la lame aiguisée,
vérifier le creux de toutes
les dents pour s'assurer de
l'absence d'angles vifs. Utiliser
la lime ronde (queue de rat)
pour rectifier l'arrondi du creux
des dents.
Emissions Control Components
The use of emission control components other than those specifically
designed for this unit is a violation of federal law.
Maintain Air Filter
1. Close choke, remove air filter cover, clean air filter area, clean or replace
filter (if damaged).
Maintain Spark Plug
Note: Use only NGK CMR7H spark plug otherwise severe engine damage can
occur.
1. Adjust spark plug gap by bending outer electrode to a 0.65 mm (0.026 in)
gap.
2. Tighten spark plug to 150 - 170 kgf•cm (130 - 150 lbf•in).
Maintain Spark Arrester Screen
Parts required: Spark Arrester Screen, Gasket.
1. Remove spark plug lead and engine cover or muffler cover if applicable.
2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering
cylinder.
3. Remove spark arrester screen cover, gaskets, and screen, from muffler
body.
4. Clean carbon deposits from muffler components.
Note: When cleaning carbon deposit, be careful, do not damage the catalytic
element inside muffler (If equipped with catalytic element).
5. Replace screen if it is cracked, plugged, or has holes burned through.
6. Assemble components in reverse order.
Fuel is VERY flammable. Use extreme care when mixing, storing or
handling, or serious personal injury will result.
Maintain Fuel Filter
1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel
tank. Pull the fuel filter from the fuel tank. Remove the filter from the line
and install the new filter (do not damage fuel line when removing the fuel
filter from the tank).
© 08/2024 ECHO Incorporated
Quick Start Guide / Guía de inicio rápido / Guide de démarrage rapide
Cutting Tooth Area /
Área de corte de dientes /
Zone de dent de coupe
Gullet Radius /
Radio de oro /
30º
Rayon d'or
Cutting Tooth Radius /
Radio de diente de corte /
Rayon de dent de coupe
SRM-2620/T
EPA Emissions Control Information
The emission control system for the engine is EM (engine modification)
and, if the second to last character of the Engine Family on the Emission
Control Information label (see example) is "B", "C", "K", or "T", the
emission control system is EM and TWC (3-way catalyst). The fuel tank/
fuel line emission control system is EVAP (evaporative emissions).
EMISSION CONTROL INFORMATION
ENGINE FAMILY: XEHXS.0214KO DISPLACEMENT: 21.2 cc
EMISSION COMPLIANCE PERIOD: 300 Hours
THIS ENGINE MEETS U.S.EPA EXH/EVP EMISSION
REGULATIONS FOR MODEL YEAR
FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
Emission Control Label
An
ONLY, information on label varies by ENGINE FAMILY).
Product Emission Durability (Emission Compliance Period)
The 50 or 300 hour emission compliance period is the time span selected
by the manufacturer certifying the engine emissions output meets applicable
emissions regulations, provided that approved maintenance procedures are
followed as listed in the Maintenance Section of this manual.
Service
• Service of this product during the warranty period must be performed by
an Authorized ECHO Service Dealer. For the name and address of the
Authorized ECHO Service Dealer nearest you, ask your retailer or call
1-800-432-ECHO (3246). Dealer information is also available on our Web
Site www.echo-usa.com. When presenting your unit for Warranty service/
repairs, proof of purchase is required.
Transportation
• During operation the muffler or catalytic muffler and surrounding cover
can become hot. Always keep exhaust area clear of flammable debris
during transportation or when storing, otherwise serious property
damage or personal injury can result.
• Always secure the unit during transportation to prevent turnover, fuel
spillage, and damage to the unit.
Short-term Storage
• Store unit in a dry, dust free place, out of the reach of children.
• Do not store in enclosure where fuel fumes can accumulate or reach
an open flame or spark, or serious personal injury will result.
Long-term Storage (Over 30 Days)
• Place the stop switch in the "OFF" position.
• Clean the exterior of the product.
• Perform all periodic maintenance.
• Tighten all the screws and nuts.
• Drain the fuel and run the unit until it stops.
• Allow engine to cool.
• Store unit in a dry, dust free place, out of the reach of children.
20
XXXX
REFER TO OWNER'S MANUAL
is located on the engine. (This is an EXAMPLE
Cancer and Reproductive Harm.
www.P65Warnings.ca.gov
.
X7152340000
Publicité
