Candy CUTCE64EXFDF Manuel De L'utilisateur page 16

7. CLEANING AND MAINTENANCE
7.1 GENERAL
Before starting to clean your oven, be sure that all control knobs
are off and your appliance is cooled off. Unplug the appliance.
Do not use cleaning materials containing particles that might
scratch the enamelledand painted parts of your oven. Use cream
cleaners or liquid cleaners, which do not contain particles.
As they might harmthe surfaces, do not use caustic creams,
abrasive cleaning powders, rough wire wool or hard tools. In the
event the excess liquids spilling over your oven should burn, it may
cause a damage to the enamel. Immediately clean up the spilt
liquids.
7.2 CLEANING THE OVEN
Make sure to unplug the oven before starting to clean it.You will
obtain best results if you clean the oven interior while the oven is
slightly warm. Wipe your oven with a soft piece of cloth dampened
with soap water after each use. Then wipe it again, this time with a
wetted cloth, and wipe it dry. A complete cleaning may be
necessary from time to time, using a liquid cleaning material. Do
not clean using dry and powder type cleaners. For products with
catalytic enamel frames, the rear and side walls of the inner frame
do not require cleaning. However; depending on usage, it is
recommended that you replace them after a certain period of time.
7.3 CLEANING THE VITROCERAMIC HOB
. Before carrying out any maintenance work on the hob, allow it
to cool down.
. Only products, (creams and scrapers) specifically designed for
aglass ceramic surfaces should be used. They are obtainable
from hardware stores.
. Avoid spillages, as anything which falls on to the hob surface
will quickly burn and will make cleaning more difficult.
. It is advisable to keep away from the hob all substances which
are liable to melt, such as plastic items, sugar, or sugar-based
products.
.MAINTENANCE:
- Place a few drops of the specialised cleaning product on the
hob surface.
- Rub any stubborn stains with a soft cloth or with slightly damp
kitchen paper.
- Wipe with a soft cloth or dry kitchen paper until the surface is
clean.
If there are still some stubborn stains:
- Place a few more drops of specialised cleaning fluid on the
surface.
- Scrape with a scraper, holding it at an angle of 30° to the hob,
until the stains disappear.
- Wipe with a soft cloth or dry kitchen paper until the surface is
clean.
- Repeat the operation if necessary.
A FEW HINTS:
Frequent cleaning leaves a protective layer which is essential to
prevent scratches and wear. Make sure that the surface is clean
before using the hob again. To remove marks left by water, use
a few drops of white vinegar or lemon juice. Then wipe with
absorbent paper and a few drops of specialised cleaning fluid.
The glass ceramic surface will withstand scraping from flat-bot-
tomed cooking vessels, however, it is always better to lift them
when moving them from one zone to another.
NB:
Do not use a sponge which is too wet.
Never use a knife or a screwdriver.
A scraper with a razor blade will not damage the surface, as long
as it is kept at an angle of 30°.
Never leave a scraper with a razor blade within the reach of
children.
Never use abrasive products or scouring powders.
. The metal surround : to safely clean the metal surround wash
with soap and water, rinse, then dry with a soft cloth.
Replacing the Oven Light Bulb
It is recommended that you leave this operation to the Authorised
Service.
Unplug the oven first and make sure that it is cold. After removing
the lid infront of the light, take the bulbout. Insert the new bulb
resistant to 300 C, which you will find at Authorised Services, into
the place of the bulb you have removed. Then fit the light
protecting lid back into its place. After that, your oven will be ready
for use.
If the oven does not operate ;
The oven may be plugged off, there has been a black out.
If the oven does not heat ;
The temperature may be not adjusted with oven's temperature
control switch.
If the oven light does not operate does not light;
The electricity should be controlled.
It should be controlled whether the ulb is defective.
Cooking (If lower-upper part does not cook equally) ;
Control the shelf locations, cooking period and temperature
values according to the manual. In case of the product doesn't
work properly and malfunctioning causes cannot be found, switch
off the product. Please do not tamper with it and call the Technical
Service.
It is important to communicate to Authorized Technical Service the
product model and it's serial number that can be found on the
rating label.
If you need any transport ;
Keep the original packaging of product and carry it with its original
packaging when needed.
Follow the transport signs on the packaging.
30° Maxi
If the original packaging is not available;
Take measure for the external surfaces (glass and painted
surfaces) of oven and hob aganist possible blows.
15 GB
Any change in the colour of the glass-ceramic surface
does not affect its operation or the stability of the surface.
Such discolorations are mostly a result of burnt food
residues or use of cookware made of materials such as
aluminium or copper; these stains are difficult to remove.
7.4 MAINTENANCE
0
8. SERVICE AND TRANSPORTATION
8.1 REQUIREMENTS BEFORE CONTACTING
TO SERVICE
8.2 INFORMATION RELATED TO TRANSPORT