Dometic Cadac 2 COOK 3 TURBO FFD Mode D'emploi page 15

Light back
• In the event of light back (where the flame burns back and ignites inside the burner or venturi housing), immediately turn
off the gas supply by firstly closing the control valve on the gas cylinder and then the appliance valve. After the flame is
extinguished, remove the regulator and check the condition of the seal; replace the seal if in doubt. Re-light the appliance.
• Should the flame persistently light back, return the product to your authorized repair agent.
Leaks
• If there is a gas leak on your appliance (smell of gas), immediately turn off the gas supply by turning the control knob clockwise
to the OFF "•" position and take it into a flame free location where the gas leak may be detected and stopped. If you wish to
check for gas leaks on your appliance, do it outside. Do not try to detect gas leaks using a flame; use soapy water.
How to check the appliance is connected to the gas supply in a sound fashion
• It is important that all gas connections have been correctly connected to prevent any gas leaks.
• The correct way is to smear the joint, i.e. where the gas container connects to the appliance, with soapy water. Turn the
appliance control knob slightly anti-clockwise to turn the gas on. If bubbles form, then there is a gas leak. Immediately turn
the gas off and disconnect the gas supply from the appliance. Check that all the connections are properly fitted. Check that
the seal is in place and in good condition before connecting the gas supply. Re-check with soapy water after refitting the gas
supply.
• If a gas leak persists, return the product to your local dealer for inspection/repair.
Fitting and changing the gas supply
Connecting the gas supply
• Before connecting the appliance to a gas supply, ensure that the rubber seal on the regulator is in position and in good
condition.
• Before connecting the hose and regulator to the appliance, check that the appliance control knob is in the OFF "•" position.
• Carry out this check each time you fit the appliance to a gas cylinder.
• Blow out any dust from the gas supply opening to prevent possible blockage of the jet.
• Fit an approved hose and regulator to the appliance.
• Ensure that the gas supply (gas cylinder/gas cartridge) is fitted in a well-ventilated location away from any source of ignition,
such as naked flames and away from other people.
• Do not twist or pinch the hose. Ensure that it is routed away from the stove body so as to prevent deterioration / damage to
the hose caused by heat.
• Make sure that the gas cylinder is kept upright at all times, connect to the cylinder by screwing on hand tight until fully
engaged.
• Ensure that a complete gas seal has been made (check for the smell of gas around the connection joint). Do not check for
leaks with a naked flame. Use warm soapy water only, applied to the joints and connections of the appliance. Any leakage will
show up as bubbles around the leakage area.
• If you cannot rectify the gas leak do not use the appliance. If you are in doubt, contact your nearest stockist.
Disconnecting and changing the gas supply
• After use, turn the appliance control knob to the OFF "•" position and close the gas supply.
• When you need to replace your empty cylinder, make sure that the gas is closed at the cylinder valve.
• Do not smoke while changing the cylinder.
• Remove the regulator from the empty cylinder.
• Attach the regulator to the full cylinder, refer to the instructions above on how to connect the gas supply.
• Apply the same care and checking procedures as if fitting a new gas cylinder.
How to check if your gas cylinder is empty
• The easiest way to check if you are low on gas is by picking up your gas cylinder.
• If you think your gas cylinder is feeling a little lighter than you'd like, weighing the bottle is a great way to see how much gas
is left. Most cylinders will have the empty weight stamped on either the neck or foot ring, and if the weight indicated on the
stamp and the weight of your cylinder are the same, you're out of gas. You can then approximate the amount of gas you have
left by the difference in weight.
Operating the appliance
• When operating this appliance, please take care to ensure that all parts are in good working order and that you have checked
for any gas leaks before lighting the appliance with every use.
• Cooking surfaces can simply be placed and are ready to use. No assembly required.
• PLEASE NOTE: Please ensure all protective packaging and plastic are removed from the appliance before use.
• The appliance is designed for use with cooking vessels of not less than 180mm in diameter and not greater than 250mm in
diameter.
• For additional safety, this appliance is fitted with a 'Flame Failure Device' (FFD), ensuring that the gas supply to the burner
shuts off immediately should the flame inadvertently go out. In the event that this happens, be sure to turn close off the gas
supply by closing the gas cylinder valve.
Precautions to observe before lighting
• Use this appliance only on a firm level surface.
• After prolonged storage, inspect the appliance for any insects and webs, which may affect gas flow.
(IMAGE SECTION 3)
(IMAGE SECTION 4)
.
13
EN