Chicco 4 FOR ME Mode D'emploi page 23

WARNING: Ensure that the stroller is locked in the open
position, by checking that the rear locking mechanism is
effectively secured.
HOW TO FIT/REMOVE THE FABRIC COVER
To fi t/remove the fabric cover more easily, these operations
must be carried out after removing the seat from the
stroller.
5. Fit the cover by inserting fi rst the upper side of the fabric fl ap
(diag. 5 A) and then the lower fl ap located on the side of the
seat (diag. 5 B). Repeat the same operation on the other side.
6. Insert the "D" rings into the appropriate holes (diag. 6).
7. Insert the waist belt into the "D" rings, as shown in diagram 7.
8. WARNING: the crotch strap is fi xed to the seat support
that is attached to the frame. To ensure the correct and safe
use of the crotch strap, it is necessary to insert it through the
hole located on the fabric cover, as shown in diagram 8.
Please refer to the paragraph "Safety Harness" for instructions
on how to use the harness correctly".
9. Fix the fabric cover to the seat, fastening the press studs as
shown in diagram 9.
10. First fi x the fabric fl aps, fastening buttons A and then the
Velcro strap B (diag. 10). Repeat the same operation on the
other side.
11. Fix the two armrest covers by fastening the press studs
(diag. 11).
WARNING: Check that the fabric cover is fi tted correctly to
the frame of the stroller.
To remove the fabric seat cover carry out the above operations
in the reverse order.
HOW TO USE THE SAFETY HARNESS
This stroller has a 5-point safety harness that features two
shoulder straps, a waist strap and a crotch strap with buckle.
WARNING: When using the safety harness with children from
birth up to approximately 6 months of age, it is necessary to
f
fi rst fi t the shoulder straps through the two adjustment holes
on the fabric backrest.
12. Insert the shoulder straps through the appropriate holes
in the fabric backrest (diag. 12 A) and check that the shoulder
straps are adjusted at the correct height for your child. If they are
not at the correct height, adjust them as required (diag. 12 B).
13. After sitting the child in the stroller, insert the 2 prongs
into the buckle and, if necessary, adjust the width of the waist
belt operating the buckles (diag. 13).
14. To unfasten the waist strap, press and pull the side prongs
at the same time (diag. 14).
WARNING: To ensure your child's safety, it is necessary to
always use the safety harness.
r
HOW TO ASSEMBLE THE SEAT IN THE REAR FACING
POSITION
WARNING. When the seat is used in this position, the bumper
bar should not be used.
15. To assemble the seat in the rear facing position, open
the seat and align the housings to the tubes, as shown in
diagram 15. To carry out this operation more easily, refer to
the positions of points A and B shown in diagram 15.
16. When the holes located on the seat are aligned to the
joints located on the frame, push the seat in a downward
direction, until a click is heard, indicating that the seat is
locked correctly into position (diag. 16).
Repeat the operation on the other side of the seat.
WARNING: Before using the stroller with the seat fi tted to
it, always check that the seat is correctly assembled to the
stroller.
HOW TO ASSEMBLE THE SEAT IN THE FORWARD FA-
CING POSITION
17. To fi t the seat in the forward facing position, open the seat
and align the housings to the tubes, as shown in diagram 17.
To carry out this operation more easily, refer to the positions
of points A and B shown in diagram 17.
18. When the holes located on the seat are aligned to the
joints located on the frame, push the seat in a downward
direction, until a click is heard, indicating that the seat is
locked correctly into position (diag. 18).
Repeat the operation on the other side of the seat.
WARNING: Before using the stroller with the seat fi tted to
it, always check that the seat is correctly assembled to the
stroller.
HOW TO REMOVE THE SEAT
The seat can be removed without removing the fabric cover.
19. Push the side knob A, located under the seat, and raise the
seat in an upward direction (diag. 19). Repeat the operation
on the other side of the seat.
HOW TO ADJUST THE BACKREST
20. To adjust the inclination of the backrest to the desired
position, press the button located on the backrest (diag.
20). Release the button to lock the backrest in the nearest
position. To raise the backrest simply push it in an upward
direction.
WARNING: The child's weight can make these operations
more diffi cult.
HOW TO ADJUST THE LEG REST
21. Press the two buttons located inside the joint of the leg
rest (diag. 21) to adjust the leg rest to the desired position.
REMOVABLE BUMPER BAR
22. To remove the bumper bar, press the two buttons located
under the armrests (diag. 22) and pull the bumper bar
towards you.
Open only one side of the bumper bar to place the child into
the stroller more easily.
WARNING: Always fasten the child with the safety harness.
The bumper bar is NOT a child restraint device.
WARNING: Never use the bumper bar to lift the stroller with
the child sitting in it.
ADJUSTABLE DOUBLE TWIST ERGONOMIC HANDLE
23. Press the button, located on the handle, to turn the
handle to the desired position and adjust its height to the
position that is most comfortable for the user (diag. 23).
The handle can be adjusted to 8 different positions.
24. WARNING: During use, the handle must not be used in
the lowered position (diag. 24 A). During use, the handles
must be in the high position, as shown in diagram 24 B.
JOINABLE HANDLE
The stroller has a joinable handle.
25. To fi t the joinable handle, press the two central levers
inside, at the same time (see diag. 25 A); then align and insert
the joints A and B into the respective holes (diag. 25 B). A
click will be heard, indicating that the joints have been fi tted
correctly into position.
23