Bosch Tronic 3500 TO Notice De Montage Et D'utilisation page 8

Installation instructions
• The small water heater is only suitable for use
with an open (unpressurised) and a single tap
connection. The warm water outlet is used for
pressure compensation and may only be
connected to suitable fittings (Order
No. BZ 13051, BZ 13071 or BZ 13062 for
undersink appliances or BZ 11113 for oversink
appliances).
• The tap outlet must always remain free. Do not use
perlators (diffusers) or shower taps.
• This appliance can be used by children aged
8 years and older as well as by persons with
diminished bodily, sensory or mental perception, or
those who lack knowledge or experience, if they are
monitored or have received instruction concerning
use and comprehend the possible dangers that can
result. Children may not play with the appliance.
Cleaning and maintenance by the user may not be
performed by unsupervised children.
• Keep children away from the appliance.
• Please monitor children to ensure that they do not
play with the appliance.
• The warm water pipe may be hot. Please inform and
instruct children appropriately.
• Do not use aggressive or abrasive cleaning
detergents!
• Do not use a steam cleaner.
Please read this installation and operating
instruction manual carefully, then act accordingly!
Store for future reference.
2 Installation instructions
2.1 Unpacking
• Inspect the new appliance for transport damage!
• Please dispose of the packaging, and if applicable, the old appliance
in an environmentally-friendly manner.
Scope of delivery (Fig. 1)
1 Appliance with operating panel
2 Installation bracket
3 TR3500TOR 5 T only:
Mounting (2 screws, 2 wall plugs)
4 Documentation
2.2 Product description
The small water heater is only suitable for open (unpressurised)
installation. It heats and stores drinking water up to approx. 85 °C.
Different temperature levels can be selected with the temperature
selector knob.
The appliance may not be operated with pre-heated water, as otherwise
the safety temperature limitation will trip.
The appliance is connected using the mains plug.
This installation and operating instruction manual describes various
appliance types:
8
• Undersink appliances with additional drip stop function and
pressure stop TR3500TO 5 T and TR3500TOR 5 T
• Oversink appliances TR2500TO 5 B
Preparations for installation (Fig. 1)
• Shut off the water supply before connecting the appliance.
Do not insert the mains plug.
• Remove the installation bracket on the appliance and break off the
retaining rings (A).
• Fix the connection cable to the rear of the appliance to suit the
required length (B).
2.3 Wall mounting
Undersink appliances TR3500TOR 5 T and TR3500TO 5 T
(Fig. 2)
• Align the appliance on the wall and use the three indents (top, left and
right on the appliance) to apply markings (A).
• Connect the markings by a pattern of crossed lines with a spirit level
(B1 and B2).
• Place the installation bracket on top at the point of intersection of the
drawn lines and mark the position for the holes (C).
• Drill the holes and insert wall plugs (D1).
• Attach the installation bracket (notch at top) to the wall using the
screws (D2).
• Suspend the appliance in the installation bracket (D3).
Exchanging appliances (Fig. 3)
• When replacing an old small water heater with this new appliance, the
existing drill holes with wall plugs can be used. Please note that the
new appliance is approx. 2 cm higher.
If the new appliance is to be flush at the top like the old appliance (E1):
• Attach the new installation bracket to the wall with the notches at
the top.
If the new appliance is to be flush at the bottom like the old
appliance (E2):
• Turn the installation bracket around and attach to the wall with
the notches at the bottom.
Oversink appliances TR2500TO 5 B (Fig. 4)
• Align the appliance on the wall and use the three indents (top, left and
right on the appliance) to apply markings (F).
• Connect the markings to a pattern of crossed lines with a spirit level
(G1 and G2).
• Place the installation bracket on top at the point of intersection of the
drawn lines and mark the position for the holes (H).
• Drill the holes and insert wall plugs (I1).
• Attach the installation bracket (notch at top) to the wall using the
screws (I2).
Exchanging appliances (Fig. 5)
When replacing an old small water heater with this new appliance, the ex-
isting drill holes with wall plugs can be used. Please note that the new ap-
pliance is approx. 2 cm higher.
• Turn the installation bracket around and attach to the wall with the
notches at the bottom (J).
2.4 Water connection
CAUTION:
Caution!
The existing fitting may not be covered with scaling.
• Do not grease the thread!
Info: Replacement for damaged threaded nozzles available from
customer service.
Tronic 2500 TO | Tronic 3500 TO | Tronic Store Advanced – 6 720 876 005 (2019/10)