Elica PRF0163523 Prescriptions De Montage Et Mode D'emploi page 23

help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
• The symbol on the product, or on the documents
accompanying the product, indicates that this appliance may
not be treated as household waste. Instead it should be taken
to the appropriate collection point for the recycling of electrical
and electronic equipment. Disposal must be carried out in
accordance with local environmental regulations for waste
disposal.
• For further detailed information regarding the process,
collection and recycling of this product, please contact the
appropriate department of your local authorities or the local
department for household waste or the shop where you
purchased this product.
Appliance designed, tested and manufactured according to:
• Safety: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 62233.
• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 5168;
EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3; ISO 3741;
EN 50564; IEC 62301.
• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; EN/IEC
61000-3-2; EN/IEC 61000-3-3. Suggestions for a correct use in order
to reduce the environmental impact: Switch ON the hood at
minimum speed when you start cooking and kept it running for few
minutes after cooking is finished. Increase the speed only in case of
large amount of smoke and vapor and use boost speed(s) only in
extreme situations. Replace the charcoal filter(s) when necessary to
maintain a good odor reduction efficiency. Clean the grease filter(s)
when necessary to maintain a good grease filter efficiency. Use the
maximum diameter of the ducting system indicated in this manual to
optimize efficiency and minimize noise.
Use
The hood is designed to be used for exhausting version.
Vapours are evacuated toward the outside by way of an exhaust pipe
fixed to the connector flange and connected to a peripheral extraction
unit (not supplied).
Connection instructions are supplied with the peripheral extraction
unit.
Caution! The evacuation pipe is not supplied and must be
purchased.
In the horizontal section, the pipe must be tilted slightly upwards
(approx. 10°) in order to more easily convey the air toward the
outside.
Connect the hood and discharge holes on the walls with a diameter
equivalent to the air outlet (connection flange).
Using the tubes and discharge holes on walls with smaller
dimensions will cause a diminution of the suction performance and a
drastic increase in noise.
Any responsibility in the matter is therefore declined.
! Use a duct of the minimum indispensable length.
! Use a duct with as few elbows as possible (maximum elbow
angle: 90°).
! Avoid drastic changes in the duct cross-section.
Operation
This product is designed to work with an Elica remote control, either
supplied with the product or purchased separately as an optional.
To control the hood via remote control, the affiliation procedure must
be carried out.
CAUTION!
To begin, the hood must be disconnected and then reconnected to
the power supply and the affiliation procedure must be carried out
within the first minute of connection to the power.
Read the instructions supplied with the remote control, which provide
detailed instructions on affiliation and correct use.
Note: the Speed 4 (and the Speed 5, where applicable) if selected,
will activate for a limited period of time after which Speed 2 is
automatically enabled.
Remote control connection (if applicable)
Once the remote control has been connected, this will be displayed
on the hood:
both LEDs flash.
Note: Using the remote control, delayed shut-down can be
programmed based on the aspiration speed (power) enabled at that
moment:
Speed 1 (low aspiration): 20 minutes
Speed 2 (medium aspiration): 15 minutes
Speed 3 (high aspiration): 10 minutes
Filter Saturation indicator lights
At regular intervals, the LEDs on the hood indicate the need to
carry out filter maintenance.
Note: The filter saturation signal is visible for a few seconds
when the hood is switched on; within this time, the saturation
indicator lights must be reset.
Flashing Green LED: carry out maintenance on the grease
filter.
Red flashing LED: carry out maintenance on the charcoal
filter (only for hoods operating in "Filtration Version").
Note: Run the "RESET FILTRES" command via the remote
control.
Activating/deactivating the filter saturation indicator light
Note: Run the procedure with the hood switched off. The
charcoal filter saturation indicator light is usually deactivated.
22