Télécharger Imprimer la page

Maytag Performance Serie Guide D'utilisation Et D'entretien page 23

Publicité

Les langues disponibles

Les langues disponibles

When
using Air Only
Check that coverings
are securely
stitched.
Shake and fluff pillows
by hand periodically
during
the cycle.
Dry item completely.
Foam rubber
pillows
are slow to dry.
NOTE: Sensor Cycles are not available
when
using the Air Only
setting.
To stop your
dryer
at any
time
Press POWER/CANCEl.
once or open the door.
To pause
the dryer
at any time
Open
the door or press START/PAUSE
once.
To restart
the dryer
Close the door and press and hold START/PAUSE
button
until dryer starts.
NOTE:
Drying
will continue
from where the cycle was interrupted,
if you close the door and
press Start within
5 minutes.
If the cycle is interrupted
for more than 5 minutes,
the dryer will
shut off. Select new cycle settings before restarting
the dryer.
Co
L uck
This feature allows
you to lock your settings to avoid unintended
use of the dryer. You can also
use the Control
I.ock feature to avoid unintended
cycle or option
changes
during
dryer
operation.
To enable
the Control
Lock feature
when
dryer
is running:
Press and hold the CONTROl_
I_OCK button
for 3 seconds.
The control
is locked when a
single beep is heard and the Control
I.ock light is on.
When
the dryer is off, it is not necessary
to press the Control
On button
before activating
the Control
I.ock feature.
To unlock:
Pressand hold the CONTROl. I.OCK button for 3 seconds to turn this feature off.
NOTE: When
the dryer is running
and Control
Lock is on, the dryer can be stopped
by
pressing the POWER/CANCEl.
or START/PAUSE
buttons,
but cannot
be restarted
until the
control
is unlocked.
Select the correct
cycle and dryness
level or temperature
for your load.
If a Sensor Cycle
is
running,
the display shows the estimated
cycle time when your dryer is automatically
sensing
the dryness
level of your
load. If a Timed Cycle
is running,
the display
shows the exact
number
of minutes
remaining
in the cycle.
Cool
Down
tumbles
the load without
heat during
the last few minutes
of all cycles. Cool
Down
makes the loads easier to handle
and reduces wrinkling.
The length of the Cool
Down
depends on the load size and dryness
level.
Drying
tips
Follow
care [abe[ directions
when they are available.
If desired,
add a fabric softener
sheet. Follow
package
instructions.
Remove the load from the dryer as soon as tumbling
stops to reduce wrinkling.
This is
especially
important
for permanent
press, knits and synthetic
fabrics.
Avoid drying heavy work clothes with lighter fabrics. This could cause overdrying of
lighter fabrics, leading to increased shrinking or wrinkling.
If you dry sheets in a mixed load or large items, rearrange the load when the signal
sounds. This will aid in the drying process.
Cycle tips
Dry most loads using the preset cycle settings.
Refer to the Sensor or Timed
Preset Cycle Settings chart (in the "Cycles"
section)
for a
guide to drying various
loads.
I)rying
temperature
and Sensor Cycles
I)ryness
are preset when you choose
a Sensor
Cycle. You can choose
a different
dryness
level, depending
on your load by pressing
the SENSOR CYCI.ES DRYNESS button
to select More
Dry, Normal,
or I.ess Dry.
If you wish to adjust the cycle
length of a Timed
Cycle,
you must press the TIME
ADJUST up or down
buttons.
Adjust
the temperature
of a Timed Cycle
by pressing
TIMED CYCI.ES TEMP until the desired temperature
is selected.
NOTE: You cannot
choose
a Sensor Cycles Dryness with
Timed Cycles.
/_,,,i?,,,i
211
f*
[i

Publicité

loading