Makita LS003GZ01 Manuel D'instructions page 24

static electricity or electrical noise could be
generated.
21. Do not leave the wireless unit in a place sub-
ject to high heat, such as a car sitting in the
sun.
22. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
23. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
24. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
PARTS DESCRIPTION
► Fig.2
1 Knob (for bevel angle)
5 Stopper arm
9 Hole for padlock
13 Vacuum button
17 Lock lever (for turn base)
21 Miter angle scale
25 Releasing button (for
right side bevel angle)
► Fig.3
1 Handle
5 Bevel angle scale
9 Latch lever (for bevel
angle)
13 Stopper pin (for carriage
elevation)
INSTALLATION
Installing the grip
Screw the threaded shaft of the grip into the turn base.
► Fig.4: 1. Grip 2. Turn base
Installing and removing dust
extraction hose
Attach the hose elbow to the upper port with the lock
button facing upwards. Insert the sleeve of the hose into
the lower port, pressing and aligning the stopper but-
tons on the sleeve with the guide notches on the port.
Make sure that the elbow and sleeve fit properly to the
ports of the tool.
► Fig.5: 1. Dust extraction hose 2. Elbow 3. Lock
2 Hex wrench
6 Lock-off button
10 Wireless activation
button
14 Blade case
18 Releasing lever (for turn
base)
22 Pointer (for miter angle)
26 Vertical vise
2 Battery cartridge
6 0° adjusting bolt (for
bevel angle)
10 Releasing lever (for 48°
bevel angle)
14 Shaft lock
25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged. Water, dust, and dirt come into the slot may
cause malfunction.
28. Do not pull and/or twist the lid of the slot more
than necessary. Restore the lid if it comes off
from the tool.
29. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
3 Adjusting screw (for
lower limit position)
7 Switch trigger
11 Wireless activation lamp
15 Blade guard
19 Grip (for turn base)
23 Turn base
27 Stopper pin (for carriage
sliding)
3 Dust bag (when replaced
with dust extraction
hose)
7 Pointer (for bevel angle)
11 Guide fence (upper
fence)
- -
button 4. Sleeve 5. Upper Port 6. Lower Port
To remove the hose elbow from the port, pull the elbow
while pressing down the lock button.
► Fig.6: 1. Lock button 2. Elbow
To remove the sleeve of the hose from the port, pull the
sleeve while pressing the stopper buttons on both sides
of the port.
► Fig.7: 1. Stopper button 2. Sleeve
Bench mounting
When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. While lowering the
handle slightly, pull the stopper pin and rotate it 90°.
► Fig.8: 1. Locked position 2. Unlocked position
3. Stopper pin
This tool should be bolted with four bolts to a level and
24 ENGLISH
4 Adjusting bolt (for maxi-
mum cutting capacity)
8 Lid (for wireless unit)
12 Lamp button
16 Sub fence
20 Kerf board
24 Sub base
28 Slide pole
4 Hose (for dust
extraction)
8 45° adjusting bolt (for
bevel angle)
12 Guide fence (lower
fence)
- -