EINHELL TC-SB 245 L Instructions D'origine page 29

•
Free-hand cuts should be made at low feed
speed so that you can guide the blade (26)
along the required line.
•
It often pays to first cut off surplus areas
around the curves and corners up to about 6
mm from the line.
•
In the case of curves which are too tight for
the installed blade to cut, you will need to
make a series of close-lying cuts up to the
front of the curved line. The surplus areas will
then drop off when you saw the final radius.
8. Transport
To transport the bandsaw, hold the pedestal (5)
with one hand and the machine frame (25) with
the other hand. Important! Never use guards to
lift or transport the equipment.
9. Cleaning, maintenance and
ordering spare parts
Danger!
Pull out the power plug before carrying out any
adjustments, maintenance or repairs.
9.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
9.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
9.3 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
Anl_TC-SB_245_L_SPK13.indb 29 Anl_TC-SB_245_L_SPK13.indb 29
GB
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Tip! For good results we
recommend high-quality ac-
cessories from
www.kwb.eu
welcome@kwb.eu
9.4 Adjusting the tension of the V-belt
(Fig. 23/ 24)
Check regularly whether the V-belt (53) is suffi ci-
ently tensioned. If the tension is too low you can
re-adjust it:
•
The height of the motor unit (2) can be adjus-
ted by means of the slot in its holder.
•
Slacken the two 6 mm socket head screws
(54) and press the motor unit (2) downwards.
(This product does not come with a 6 mm
hex key)
•
Once the V-belt (53) has the necessary tensi-
on, re-tighten the 6 mm socket head screws
(54).
•
Caution! After the tension has been adjusted
you must make sure that the motor shaft and
the shaft of the lower blade pulley (7) are par-
allel with each other.
•
If this is not the case, use the two adjustment
screws (55) to correct the tilt of the motor unit
(2).
10. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
11. Storage
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempe-
rature is between 5 and 30 °C. Store the electric
tool in its original packaging.
- 29 -
!
11.01.2024 14:09:26 11.01.2024 14:09:26