GYS KRYPTON 321 DC TRI Mode D'emploi page 41

User manual
MEMORISING AND RECALLING JOBS
• Job Out/Job In
The settings in use are automatically saved and remembered the next time you turn on the machine.
In addition to the current settings, it is possible to save and recall «JOB» configurations.
There are 50 JOBS for each welding process, with memory storage for:
- The main parameter,
- The secondary parameter (MMA, TIG),
- Sub-processes and trigger modes.
Recall an existing «Job Out» configuration:
- Press the «JOB» button on the keypad, select it using the thumbwheel
- Confirm by pressing the button on the thumbwheel,
- The display shows the previously stored JOB number (01 to 50) flashing. Si aucun JOBS n'est créé, l'afficheur indique «Empty»
- Turn the thumbwheel to select the JOB you wish to retrieve,
- Confirm by pressing the button on the thumbwheel,
- The recall is carried out / immediate exit from the menu.
Save a setting «JOB IN»:
- Press the «JOB» button on the keypad, select it using the thumbwheel
- Confirm by pressing the button on the thumbwheel,
- The display indicates a memory slot (01 to 50) while flashing. Fast blinking = JOB already in use. Slow flashing = free space.
- Turn the thumbwheel to select a memory slot for the configuration to be saved,
- Confirm by pressing the button on the thumbwheel,
- The entry is completed / immediate exit from the menu occurs.
Supprimer un JOB :
- Press the «JOB» button on the keyboard, select with the thumbwheel
- Confirm by pressing the button on the thumbwheel,
- Turn the wheel to select the JOB you wish to delete and hold down the «JOB» button on the keyboard for 3s.
- A DELETE message is displayed on the keyboard, the previously selected JOB is now deleted.
• Quick Load «q.L. «:
Quick Load is a non-welding JOB retrieval mode (50 max) and is only available when using TIG.
JOB recalls are performed by briefly releasing (<0.5s) the torch buttons.
This mode is accessed via the «JOB» menu, then the submenu
entering the JOB number at the end of the sequence to be recalled (the sequence starts at the first JOB). At least 2 JOBS must be saved prior to that.
Eg: if JOBS 2, 5, 7 and 10 have been created and the user enters number 7, then the JOBS recalled will be 2, 5 and 7.
When the mode is activated, the first JOB is recalled and displayed on the HMI (in the example: JOB 2).
The recall is looped: when the last JOB in the queue is reached (example: JOB 7), the following one will be the first in the sequence (in the example:
JOB 2).
Welding is activated by pressing the button for longer than 0.5s.
The HMI will behave with the relevant information:
- The JOB is permanently displayed as well as the parameters (TIG LIFT/HF..., 2T/4T.../ Pulse/Spot...).
- The weld cycle is accessible and can be modified (the JOB is adjustable*),
- The menus are accessible and modifiable. Example:
• JOB 5, amended, JOB IN / JOB 5, the JOB is overwritten with the new parameters and saved.
• JOB 5, amended, JOB IN / non-existent JOB, it will be integrated into the current q.L. if, and only if, the new JOB X is a smaller number
than the JOB already entered.
- The JOB recall is disabled when navigating the welding cycle settings or one of the two menus.
* A JOB is de-set by a HMI action (welding parameter adjustment, JOB recall ...), welding is then allowed with the new settings. If a JOB recall is
initiated, then the first JOB in the sequence is recalled.
CHAINING «CHn»:
Chaining is a complex JOB recall mode (50 max) and only possible in TIG Standard and TIG Pulse mode (all the JOBs set in 2T are changed to 4T):
- When not welding, briefly (<0.5s) releasing the torch button will scroll through all stored JOBS one by one. On reaching the last item in the list, the
selection goes back to the first item.
- Welding is activated by pressing the top button for 0.5s, whereas in the standard mode it is activated immediately upon pressing this button.
- During welding, briefly releasing the button (<0.5s) will recall a defined number of consecutive JOBs, also known as the sequence, starting from the
previously recalled JOB when not welding.
This mode is accessed via the «JOB» menu, then the submenu
entering a number of JOBS that make up the sequence. At least 2 JOBS must be saved prior to that.
Spot welding jobs (SPOT, TACK), are no longer part of the list of saved JOBS (they are transparent).
Translation of the original
instructions
Job
q.L.
CHn
KRYPTON 231 DC FV / 321 DC TRI
Job
Out
,
Job In
,
In
,
q.L.
. Disabled by default
CHn OFF
. Disabled by default
OFF
, the user activates this mode by
, the user activates this mode by
41