SSS Siedle ST 10-01 Information Du Produit page 12

b) Terminals E and G can be option-
ally used for integrating buttons or
actuators provided by the customer
for expanding the function of the
ST(E) 10­...
c) In the case of telecommunica-
tion installation cable (J­Y(St)Y ...)
with a core diameter of 0.8 mm
(0.6 mm), there is a maximum
distance of 150 m (75 m) between
power supply (e.g. NG 706­...) and
Siedle Touch ...
d) Observe the connection informa-
tion in the BTLM 651­... product
information: To operate the bus
door loudspeaker module Plus with
activated additional amplifier, an
additional supply (22–32 V DC,
e.g. NG 706­...) is required.
Additional power supply with the
ANG 600­... (48 V DC) is not pos-
sible!
Installation: In-Home bus
2 Connection pcb for flush­
mounted door stations (shown with
SBTLM 651­... connection pcb)
3 Connection pcb for surface­
mounted door stations
4 In­Home bus wiring diagram
Installation: Access Professional
5 Connection pcb for flush­mounted
door stations (shown with SATLM
connection pcb)
6 Connection pcb for surface­
mounted door stations
7 Access wiring diagram
Terminal assignment (ST 10)
6, 1 Triggering
Door loudspeaker
E, G Electrically isolated input,
12 V AC / 8–30 V DC
E (+), G (–), or Potential-
free input
Da, Db Data cable Vario bus
+, – Supply voltage
48V 20–48 V DC
b, c Button illumination
12 V AC for potential-
free button T1/T2
12
T1, T2 Potential-free button
(system-independent, for
customer's applications,
e.g. activation of outside
light)
LAN ext. Network connection for
configuration – LAN ext:
192.168.1.250 (upon
delivery)
Terminal assignment (SBTLM 651)
+, – Additional supply
(24 V) 22–32 V DC, audio
amplifier
Acoustic status indication
The ST(E) 10-01 enables individual
acoustic status indication (audio
feedback) via the built-in additional
loudspeaker for the "call", "door
release" and "speak" statuses.
As part of the scope of supply, a
standard audio tone per status can
also be configured. An audio file
(MP3) can be imported per status for
a voice output.
Configuration
The user data (e.g. name, call num-
bers, acoustic status indication) and
device settings (e.g. input contacts,
network, brightness) are configured
via the ST(E) 10-... configuration
interface using a web browser via
the network. Access data is required
to log into the configuration inter-
face.
Web configuration access data
(upon delivery)
User name admin
Password admin
We recommend changing the access
data after you log in for the first
time.
Keep the access data safe. Only
Siedle Engineering can reset for-
gotten access data.
Cleaning mode
Activate cleaning mode prior to
cleaning the display: Tap the top
left corner of the display six times
to activate cleaning mode (a
spray bottle appears along with a
timer that counts down to 0) and
deactivate the touch functions for
15 seconds.
Care instructions
Clean your display carefully and only
with a soft, slightly moistened cloth.
Dry, aggressive cleaning agents and
abrasive detergents can damage the
surface! Detailed care instructions
are located in the download area of
www.siedle.com.
Servicing
The functional unit can be com-
pletely exchanged if required.
In the event of replacement, contact
Siedle service.
Before replacement, make sure
you back up the Siedle Touch data
(e.g. button layout and configura-
tion) and transfer it to the new
Siedle Touch after replacement.
Specifications
Operating voltage: 20–48 V DC
Operating current: max. 700 mA
(current consumption in idle state:
365 mA) at 30 V DC
Protection system: IP 65 (from the
front), IK 08
Ambient temperature:
–20 °C to +55 °C
Cut-out (mm) W x H: 238 x 165
Resolution: 1280 x 800 pixels
Current consumption:
• approx. 8.4 W (at reduced load: no
video, panel backlight at 10 %)
• max. approx. 24 W (at full load:
video on and panel backlight at
100 %)