HIKOKI WR 36DF Mode D'emploi page 12

English
(2) Regarding the temperatures and charging time of the
rechargeable battery
The temperatures and charging time will become as
shown in Table 2.
Model
Type of battery
Charging voltage
Temperatures at which the battery
can be recharged
Charging time for
battery capacity,
approx.
(At 20°C)
1.5 Ah ( 2 unit)
Multi
volt 2.5 Ah ( 2 unit)
battery
4.0 Ah ( 2 unit)
Number of battery cells
Charging voltage for USB
Charging current for USB
Weight
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2 – 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
Table 2
UC18YSL3
Li-ion
14.4–18 V
0°C–50°C
1.5 Ah 15 min
2.0 Ah 20 min
2.5 Ah 25 min
20 min
3.0 Ah (BSL1430C,
BSL1830C: 30 min)
26 min
4.0 Ah
(BSL1840M: 40 min)
5.0 Ah 32 min
6.0 Ah 38 min
8.0 Ah 52 min
20 min
32 min
52 min
4–10
5 V
2 A
0.6 kg
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
charge indicator lamp of the charger lights for 0.3 seconds,
does not light for 0.3 seconds (off for 0.3 seconds). In such
a case, fi rst let the battery cool, then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service Center.
MOUNTING AND OPERATION
Action
Removing and inserting the
battery
Charging
Remaining battery indicator
Removing and mounting the hook
How to use the hook
Mounting the socket *1
Mounting the socket *1
Reversing the rotational direction
Switch operation
How to use the LED light
Tightening mode selector
function *3
Auto stop mode selector switch
Auto stop mode
Auto slow mode
Charging a USB device from a
electrical outlet
Charging a USB device and
battery from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*1 Installing a socket
Select the socket to be used.
[WR36DF]
(1) Slide the O-ring out of the groove, then align the hole
of the socket with the hole of the anvil and insert the
anvil into the socket.
(2) Insert the pin into the socket.
(3) While making sure that the pin doesn't fall, attach the
O-ring to the groove on the socket.
[WR36DG]
(1) Align the square portions of the socket and the anvil
with each other.
(2) Make sure to fi rmly install the socket by pushing it all
the way into the anvil.
(3) When removing the socket, pull it out of the anvil.
12
Figure
3
4
5
6
7
(WR36DF) 8
(WR36DG) 9
10
11
*2 12
13
14
15
16
17-a
17-b
18
19
―
Page
2
2
2
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
235