Publicité
Les langues disponibles
Les langues disponibles
•
When clearing jammed materialor servicing the
machine, make sure the switch is off and the
battery pack is removed. Unexpected starting of the
machine while clearing jammed material or servicing
may result in serious personal injury.
•
Carry the machine with the machine switched off
and away from your body. Proper handling of the
machine will reduce the likelihood of accidental
contact with a moving cutter, line or blade.
•
When transporting or storing the machine, always
fit the cover on metal blades. Proper handling of
the machine will reduce the likelihood of accidental
contact with the blade.
•
Only use replacement cutters, lines, cutting heads
and blades specified by the manufacturer. Incorrect
replacement parts may increase the risk of breakage
and injury.
•
When clearing jammed material or servicing the
machine, make sure the switch is off and the battery
pack is removed.Unexpected starting of the machine
while clearing jammed material or servicing may
result in serious personal injury.
Other general safety information
•
Deactivate the product before you move to another
area. Always remove the battery when passing the
product to another person.
•
Never put the product down unless you have
deactivated it and removed the battery. Do not leave
the product unsupervised when it is switched on.
•
The cutting tool does not stop immediately after the
product is turned off.
•
Before using the product and after any impact,
check for signs of wear or damage and repair as
necessary.
•
If anything jams in the cutting attachment while
you operate the product, stop and deactivate the
product. Make sure that the cutting attachment stops
completely. Remove the battery before you clean,
inspect or repair the product and/or the cutting
equipment.
•
Do a check of the product before use. Refer to
Safety devices on the product on page 14 and
Maintenance on page 19 . Do not use a defective
product. Do the safety checks, maintenance and
service instructions described in this manual.
•
Faulty cutting attachment can increase the risk of
accidents.
•
Check the gear for dirt and cracks. Clean off grass
and leaves from the gear using a brush. Gloves
should be worn when necessary.
•
Always ensure that ventilation openings are kept
clear of debris.
•
Check that the trimmer head is completely attached
to the trimmer.
•
All covers, guards and handles must be fitted before
starting.
•
Check that the product is in perfect working order.
Check that all nuts and screws are tight.
12
•
Check that the trimmer head and trimmer guard are
not damaged or cracked. Replace the trimmer head
or trimmer guard if it has been exposed to impact
or are cracked. Always use the recommended guard
for the cutting attachment you are using. Refer to
Accessories on page 23 .
•
This product is a dangerous tool if you are not
careful or if you use the product incorrectly. This
product can cause serious injury or death to the
operator or others.
•
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
the appliance.
•
Never allow children to use or be in the vicinity of the
machine. Since the machine is easy to start, children
may be able to start it if they are not kept under
full surveillance. This can mean a risk of serious
personal injury. Therefore disconnect the battery
when the machine is not under close supervision.
•
Never allow children or other persons not trained in
the use of the product and/or the battery to use or
service it.
•
Store the equipment in a lockable area so that it is
out of reach of children and unauthorized persons.
•
Keep hands and feet away from the cutting area
at all times and especially when switching on the
motor.
•
Keep your hands and feet away from the cutting
attachment until it has stopped completely when the
product is deactivated.
•
Do not remove the cut material, or let other persons
remove cut material, while the product is activated
or the cutting equipment rotates, as this can result in
serious injury.
•
Keep in mind that it is you, the operator that is
responsible for not exposing people or their property
to accidents or hazards.
•
Under no circumstances may the design of the
product be modified without the permission of the
manufacturer. Always use original accessories. Non-
authorized modifications and/or accessories can
result in serious personal injury or the death of
the operator or others. Your warranty may not
cover damage or liability caused by the use of non-
authorized accessories or replacement parts.
•
The only accessories you can operate with this
product are the cutting attachments recommended
in the Accessories chapter. Refer to
page 23 .
•
Never use a product that has been modified in any
way from its original specification
•
Never use a product that is faulty. Carry out the
safety checks, maintenance and service instructions
described in this manual. Some maintenance and
service measures must be carried out by trained
Accessories on
1859 - 006 - 21.05.2024
Publicité
