Publicité
Les langues disponibles
Les langues disponibles
occur for technical reasons and have no negative
consequences.
•
Noise emissions are greater when loaded.
•
Before each training, make sure the protective devices are
operational and bolt and plug connections are tight.
•
Wear appropriate (sports) shoes during the training.
MAINTENANCE
Carry out maintenance activities at regular intervals. The tasks listed
below should be carried out at least every 20 hours of operation.
•
Check moving parts of the device. If they need lubrication, use
a bicycle bearing grease.
•
Check the conditions of such parts as bolts and nuts.
Make sure they are tight.
•
Wipe the sweat off the device after each training. Make sure the
display does not come in contact with water or moisture.
•
Clean the product with soapy water only. Do not use cleaning
agents.
•
Store the device in a dry and warm place.
•
Do not expose the device to direct sunlight.
REPLACING BATTERIES
Poor display view or no information displayed at all means
the batteries need to be replaced.
Remove the battery cover and replace the old batteries with two new
ones. When replacing the batteries, respect the '+' and '–' polarities.
If the display does not operate correctly after a restart, remove
the batteries for a few minutes and insert them back.
CAUTION! Used batteries are out of the scope of the warranty. They
contain harmful substances (such as cadmium, mercury, or lead) and
should not be thrown away with household waste. Dispose of them in
an appropriate battery recycling centre.
ENVIRONMENT
The device is delivered in a package to protect it against any possible
transport damage. The packaging is made from non-processed
material and can be recycled. Throw the materials to appropriate
colour containers for selective waste collection.
Protect the environment and do not throw used batteries
into household wastes. Return them to the point of sale
or a special recycling centre.
Used electrical equipment (including the computer and
power supply) are recyclable. Do not throw them out with
household waste as they may contain substances dangerous to the
health and environment. You can actively contribute to sustainable
use of natural resources and the protection of the natural
environment by handing the used device to a recycling centre for used
electrical devices.
ASSEMBLY
The device must be assembled carefully by an adult. In case of doubt,
ask a more experienced person for help.
•
Prior to the assembly, make sure the set contains all
the listed elements and whether none of the parts was
damaged during transport. If any parts are missing or you have
any other reservations, contact the seller.
•
Have a look at the drawings and explanations and follow the
assembly manual when assembling the device.
•
Be careful during the assembly. There is a risk of injury when
using the tools and parts.
•
Remember to keep your surroundings safe. Do not let tools
and parts lie around in chaos. Remember that plastic foil and
bags pose o suffocation risk to small children.
•
Assembly parts necessary for a specific step in
the assembly manual are shown in pictures and included in
instructions. Use the elements indicated in the assembly
manual.
•
Do not tighten parts completely during the first stages
of the assembly. Tighten connections after all parts are placed
and fitted properly.
•
The manufacturer may have assembled some parts.
ASSEMBLY DIAGRAM (→ See page 2)
ATTENTION! Do not use parts other than those provided by the
manufacturer.
PARTS LIST
NO.
DESCRIPTION
1
Main frame
2
Front bottom tube
3
Guide rail
4
Rear support frame
5
Right support frame
6
Left support frame
7
U baffle plate
8
Handlebar
9
Square neck bolt M8*L45
10
Bolt M12*155*16
11
Hex bolt M10*105
12
Hex bolt M8*125*L15
13
Hex socket pan head screw M8*16
Cross recessed pan head tapping screws
14
ST4.2*18
15
Cap nut M8
16
Nylon nut M6
17
Nylon nut M8
18
Nylon nut M10
19
Spring washer D8
20
Flat washer D8*φ16*1.5
21
Flat washer D10*φ32*2
22
Flat washer D10*φ20*1.5
23
Adjustable bolt M6*36
24
U-shape washer
25
Spacer φ9*φ12*35.8
26
Spacer φ13*φ8.2*3
27
Bearing
28
Saddle
29
PU wheel
30
Bolt
31
Square tube plug
32
Front end cap
33
Rear end cap
34
Fabric belt
35
Foam grip
36
Cushion
37
Paddle
38
Plug
39
Round magnet with bracket
40
Round tube plug
41
Sensor wire
42
Extension wire
43
Ball cap
44
Cross screw M5X15
45
Rubber case
ASSEMBLY MANUAL (→ See page 3)
CAUTION! Follow the steps below during the assembly and use tools
supplied with the product. Prepare sufficient space for the assembly
operation. It is advisable to assemble the product with another person
because of the weight of some elements.
FOLDING AND UNFOLDING (→ See page 5)
NOTE! Before folding the product, make sure all bolts are tight.
NOTE! Mind your fingers when folding so that they don't get pinched.
Unscrew the knob with the flat washer. Fold the slider track as shown.
Finally, secure the slider to the main framewith the knob with the flat
washer.
ADJUSTMENTS
Resistance adjustment
In order to increase the resistance, turn the resistance knob clockwise.
In order to decrease the resistance, turn
the resistance knob counterclockwise.
EN
QUANTITY
1
1
1
1
1
1
2
1
2
4
1
3
8
2
2
2
3
1
10
16
1
2
2
2
3
6
12
1
6
1
1
2
2
1
2
2
2
1
1
2
1
1
2
4
1
12
Publicité
