Skil 7125 Notice Originale page 8

Delta sander
INTRODUCTION
• This tool is intended for dry sanding and finishing of
wood, painted surfaces, plastic, metal and filler; it is
particularly suitable for working on edged, narrow and
other hard-to-reach places
This tool is not intended for professional use
•
• Read and save this instruction manual 3
TECHNICAL DATA 1
TOOL ELEMENTS 2
A Extension for vacuum cleaner
B On/off switch
Sanding speed selection wheel
C
D Ventilation slots
E Hex key
F Storage for hex key
G Delta sanding sheet
H Pad screw
J Delta backing pad
K Finger attachment*
L Finger-shaped sanding sheet
* NOT STANDARD INCLUDED
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference. The term
"power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
7125/7126
d) Do not abuse the cord. Never use the cord for
e) When operating a power tool outdoors, use an
f) If operating a power tool in a damp location is
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use
b) Use personal protective equipment. Always wear
c) Prevent unintentional starting. Ensure the switch
d) Remove any adjusting key or wrench before turning
e) Do not overreach. Keep proper footing and balance
f) Dress properly. Do not wear loose clothing or
g) If devices are provided for the connection of dust
h) Do not let familiarity gained from frequent use of
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power
b) Do not use the power tool if the switch does not turn
c) Disconnect the plug from the power source and/
8
Water entering a power tool will increase the risk of
electric shock.
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
at all times. This enables better control of the power tool
in unexpected situations.
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
or remove the battery pack, if detachable, from