ROSIERES TR631NOX/1 Instructions D'utilisation Et D'installation page 4

SAFETY INSTRUCTIONS
• Leaning or sitting on the open door of the dishwasher could cause it to tip over.
• If the appliance breaks down or stops working properly, switch it off, turn off the water supply and do
not tamper with it. Repair work should only be carried out by an approved service agent and only gen-
uine spare parts should be fitted. Any failure to follow the above advice may have serious conse-
quences for the safety of the appliance.
• Water left in the machine or on the dishes at the end of the wash programme should not be swal-
lowed.
• The dishwasher is designed for normal kitchen utensils.
Objects that have been contamined by petrol, paint, traces of steel or iron, corrosive chemicals, acids
or alkalis must not be washed in the dishwasher.
• WARNING: The appliance and its accessible parts become hot during use. Care should be taken to
avoid touching heating elements.
• Cleaning and user maintenance shall not be made by children without supervision
• WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.
• NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with
a lid or a fire blanket.
• WARNING: Danger of fire: do not store items on the cooking surfaces.
• WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric
shock.
• During use the appliance becomes hot. Care should be taken to avoid touching h eating elements
inside the oven.
• WARNING: Accessible parts may become hot during use. Young children must be kept away.
• Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass, the glass
hob lid or the glass hob surface since they can scratch the surface, which may result in shattering of
the glass.
• Disconnect the appliance from the mains electricity supply before carrying out any work or mainte-
nance on it.
• The oven must be switched off before removing the guard, after cleaning, the guard must be
replaced in accordance with the instructions.
• Only use the temperature probe recommended for this oven.
• WARNING: Never remove the oven door seal.
• Only use the oven for its intended purpose, that is only for the cooking of foods: any other use, for
example as a heat source, is considered improper and therefore dangerous. The manufacturer
cannot be held responsible for any damage resulting from improper, incorrect or unreasonable usage.
• When you place the shelf inside, make sure that the stop is directed upwards and in the back of the
cavity. The shelf must be inserted completely into the cavity.
• When inserting the grid tray pay attention that the anti-slide edge is positioned rearwards and
upwards.
• Do not use a steam cleaner or high pressure spray for cleaning operations.
• Any spillage should be removed from the lid before opening.
• The hob surface must be allowed to cool down before closing the lid.
- CAUTION: glass lids may shatter when heated. Turn off all the burners before shutting the lid.
• If present, do not to stare into halogen lamp hob elements.
• Use only hob guards designed by the Manufacturer of the cooking appliance or indicated by the
Manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the
appliance. The use of inappropriate guards can cause accidents.
• Do not put metallic objects such as knives, forks, spoons or lids on the hob. They could heat up.
• Do not touch the heat zones during operation or for a while after use.
• Do not place anything on control panel.
• WARNING: Avoid possibility of electric shock - ensure the appliance is switched off before replacing
the lamp.
• If the range is placed on a base, measures must to be taken to prevent the appliance slipping off the
base.
• The appliance must not be installed behind a decorative door in order to avoid overheating.
• The connection to the power source must be carried out by a suitably qualified professional. In order
to have an installation compliant to the current safety legislation the product must be connected only
placing an omnipolar breaker, with contact separation compliant to the requirements for overvoltage
04 GB