EINHELL 43.001.10 Mode D'emploi page 16

Anleitung KGSL 250-2 SPK 1
GB
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the left
until the pointer (a) coincides with the required
angle value (15).
Re-tighten the locking nut (12) and make the cut
as described in Section B.).
F.) Precision adjustment of the stop for 45° mitre
cuts (Fig. 8/9)
Lower the machine head (4) and fix with the lock
pin (16).
Fix the rotary table (8) in 0° position.
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the left
until it coincides at 45°.
Place the 45° stop angle (A) between the saw
blade (5) and the rotary table (8).
Slacken the counter nut (25) and adjust the
setting screw (26) until the angle between the
saw (5) and the rotary table (8) equals exactly
45°.
G.) Mitre cuts 0°-45° and rotary table 0°-45°
(Fig. 10)
The KGSL 250/2 can be used to make mitre cuts on
the left at an angle of 0°-45° relative to the work top
and 0°-45° relative to the stop rail.
Lift the machine head (4) to its top position.
Undo the rotary table (8) by slackening the
locking handle (10) and pressing the latch (11).
Adjust the rotary table (8) by its handle (2) to the
required angle (see also Section D).
Retighten the tightening screw (10) in order to
secure the turntable in place.
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the left
until it coincides with the required angle value (in
this connection see also section E).
Screw the tightening screw (12) back down
again.
H.) Dust bag (Fig. 2)
The saw is equipped with a bag (14) to collect
sawdust and chips. You can pull off the sawdust bag
(14) to the rear by pressing together the two clips
(27). To empty the bag, undo the zip at the bottom.
I.) Replacing the saw blade (Fig. 5/11)
Pull out the power plug.
Swing up the machine head (4).
Unscrew the two bolts (27, 28) and flip the cover
plate up together with the saw blade guard (6).
Press the saw shaft lock (17) with one hand while
holding the wrench (32) on the flange bolt (25)
16
30.07.2004 9:00 Uhr Seite 16
with the other.
Firmly press on the saw shaft lock (17) and
slowly rotate the flange bolt (25) in clockwise
direction. The saw shaft lock engages after no
more than one rotation.
Now, using a little more force, slacken the flange
bolt (25) in clockwise direction.
Turn the flange bolt (25) until it is completely
removed.
Take the blade (5) off the inner flange and pull
out downwards.
Mount the new saw blade in reverse order and
fasten.
Important! The cutting bevel of the teeth, i.e. the
direction of rotation of the saw blade, has to
conform with the direction of the arrow marked on
the housing.
Clean the saw blade flanges thoroughly before
mounting the saw blade.
Reattach the movable blade guard (6) in reverse
order.
Before using the saw again, check that the safety
devices are in good working order.
Important: Every time that you change the saw
blade, check to see that it spins freely in the
groove of the turntable in both perpendicular and
45° angle settings.
J.) Laser function (Fig. 13)
You can switch the laser ON and OFF with the
switch (a).
The laser directs a beam onto the workpiece.
Extremely precise cuts can be made using the
laser function.
8. Maintenance
Keep the machine's air vents unclogged and
clean at all times.
Remove dust and dirt regularly from the machine.
Cleaning is best done with compressed air or a
rag.
Re-lubricate all moving parts in regular intervals.
Never use caustic agents to clean plastic parts.
9. Ordering replacement parts
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required