Publicité
Page 12 of 12
Retirez l'autre boulon surligné en rouge (Photo 1), insérez l'entretoise (article 5 ou 6) dans le
•
support de montage du moteur et faites pivoter l'ensemble pour l'aligner et poussez/vissez le
boulon.
À l'aide d'une clé dynamométrique, serrez les boulons au couple de serrage spécifié par le
•
fabricant dans le manuel d'entretien.
À ce stade, vérifiez que les autres boulons de l'assemblage soient complètement serrés et que
•
les capuchons de boulon (article 16) sont appliqués sur les boulons à tête cylindrique.
Répétez le processus pour le côté droit.
•
Rattachez complètement vos carénages, puis offrez les protections sur les blocs de montage et
•
serrez, en vous assurant que la bobine soit orientée dans la bonne direction (indiqué en haut de
la page 3).
Une fois que tous les boulons ont été serrés, appliquez les capuchons de protection sur la
•
protection.
Note : Le réglage du couple des boulons du moteur/bobine doit être vérifié à intervalles
Voir plus de produits R&G pour votre moto via ce lien :
R&G Racing | All Products for KTM - RC 390 (2022) (rg-racing.com)
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may
make design changes which do not diminish their performance or visual appeal and supplying them in such state
shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been
given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it has
chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the
Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge
unless the workmanship has been disturbed.
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option
either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified
or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering
practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise
its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned.
These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned
direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to
original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a
25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase).
The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of
purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
réguliers lors de la maintenance/entretien de routine.
ISS 1 - 25/01/2023 (TB)
CONSUMER NOTICE
The Buyer is responsible for ensuring that the warranty on the
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
CP0546BL
Email:
info@rg-racing.com
Publicité
