R&G LP0164BK Instructions De Montage page 7


Soulevez le nouveau support de plaque/Passage de roue dans la position initiale puis
utiliser les 4 boulons M6x20mm, écrous et rondelles (ARTICLES 3, 4 et 5) pour fixer la
position.

Replacer les 2 boulons inviolables comme à l'origine ou remplacez-les par les boulons
fournis (ARTICLE 7).

Remettre soigneusement le capot arrière.
Page | 14

Remettre les 2 sièges.

Remettre la plaque d'immatriculation sur le nouveau support de plaque (cela peut
nécessiter un perçage).

IMPORTANT: Si vous installez une grosse plaque, il y a un risque que la plaque entre en
contact avec la roue arrière en cas de choc sur la route (bosse, grosse charge etc...). Il
est de votre responsabilité de vérifier que cela ne puisse pas se produire. Ne pas
effectuer ces vérifications peut entrainer des dommages ainsi que des blessures graves
pour le pilote.

Selon la loi locale, monter les réflecteurs (article 10) aux emplacements appropriés.
Revérifiez que les clignotants et les feux de plaque fonctionnent bien avant de prendre
la route.
Ces instructions de montage sont disponibles au téléchargement sur :
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes
which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer
acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G's
order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular
purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of
charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not
affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the
purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G's
or manufacturer's instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and
subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and
otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do
not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable
condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at
the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless
within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
C
OUPLES DE SERRAGE RECOMMANDES
M4 BOULON = 8Nm
M5 BOULON = 12Nm
M6 BOULON = 15Nm
M8 BOULON = 20Nm
M10 BOULON = 40Nm
ISSUE 1 06/06/2014 (NSY)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
Unit 1 Shelleys Lane, East Worldham, Alton, Hants GU34 3AQ
www.rg-racing.com
LP0164
www.rg-racing.com
Email: info@rg-racing.com