Kinderkraft MOOV 2 Guide D'utilisation page 26

The sketches show the installation of one type of inflatable or maintenance-free wheel. The installation / removal method
for both wheels is the same .
WARNING! If the pram is equipped with inflatable wheels: the
value is indicated on the wheel tyres.
WARNING! Before using the buggy, make sure that all the
wheels are properly installed.
III CARRYCOT ASSEMBLY
Start the assembly of the carrycot by sliding the loose part of the frame (8) into the carrycot slots (7) (PIC. F). Make sure
that the snap buttons are locked (PIC.G). and zip around the perimeter of the attached part (PIC.H) (Set the position of the
rod under the carrycot with the straps and secure it with the fasteners (PIC.I). Now, the carrycot can be fastened into the
pushchair's frame (hear the lock sound of both sides of the pushchair) (PIC.J). The straps should be hidden under the
included mattress when using the pushchair in the carrycot version. When using the carrycot version of the pushchair, the
straps on the sides of the seat (2 on the left and 2 on the right) and under the footrest must remain unfastened. -CAUTION!
When the child starts to sit up independently, attach an additional harness at the attachment points indicated in (PIC.K).
WARNING! THE PRAM BODY CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
IV ASSEMBLY/DISASSEMBLY OF THE BUMPER BAR, SHADE, FOOT MOOF AND CUP HOLDER
The bumper bar (6) can be used in both the carrycot and stroller versions of the pushchair. Slide the ends of the bumper
bar into appropriate slots until you hear the lock sound on both sides (PIC. L). The bumper bar can be detached from the
frame partly or as a whole by pressing the button on its side/sides.
NOTE! INSTALL THE CANOPY BEFORE USING THE BUGGY
Begin the assembly of the shade (9) by sliding the plastic mountings on the slideway on the frame of the carrycot/seat
(PIC. M). Correct locking is signalised by a gentle click. In the end, secure the shade with hook and loop fasteners, fastening
them into the carrycot/seat. To disassemble the shade, press the buttons (PIC.N) and slide out the mountings from the
slideways.
Begin the assembly of the footcover (10) by slipping on the cover. Attach the top part of the cover by the snaps located on
both sides of the footcover (PIC. II). Wrap the cover around both sides of the bar, and then insert the buttons through the
loops on both sides (PIC. III). Assemble the cup holder (14) on the pin on the right side of the pushchair. (PIC. P).
V TURNING THE CARRYCOT INTO THE SEAT
To turn the carrycot into the seat, first connect the ends of the removed straps behind the backrest and under the seat
and the footrest (PIC.Q). When the straps are correctly fastened, the seat should look as shown in (PIC.R), the seat can be
fitted forwards or backwards (adjustment of seat angle described in section X). If you want to use the stroller with a
mattress, put the shoulder, waist and crotch straps through the slots in the mattress.
VI ASSEMBLY OF THE BAG, MOSQUITO NET, RAIN COVER
The pushchair set includes: bag (12), fabric hangers (13), rain cover (16) and a mosquito net (17). Hang the bag on the
parent's handle and secure with fasteners. (PIC. S).
Place the mosquito net/ rain cover on the pushchair, secure it with a hoop and loop fasteners around the frame (PIC. T).
VII ASSEMBLY/DISASSEMBLY OF THE CAR SEAT
Slide the adapters into the slots in the frame until you hear the lock sound (PIC. U). Adapters shall be slightly leaned
towards the parent. Slide the car seat onto the adapters and make sure it's secured correctly. The pushchair with a car
seat is shown on (PIC. V). To disassemble the adapters from the pushchair's frame, press the lock buttons on each adapter
(PIC.W)
WARNING! The car seat must be always placed on the frame
back to the direction of travel (the child should face the person
pushing the buggy).
VIII USING THE BRAKE
The pushchair is equipped with a foot brake for parking located on the rare axle. Press the brake pedal downwards to
activate the brake. Unlocking the break happens by lifting the pedal upwards (PIC.X).
IX DISSASEMBLY OF THE PUSHCHAIR
To disassemble the carrycot/seat of the frame, press the buttons located on both sides, placing your fingers at the bottom
26