Craftsman 139.18452D Manuel D'instructions page 17

WARNING
CAUTION
INSTALLATION STEP 6
Install the Door Control
Locate door control within sight of door, at a minimum
height of 5 feet (1.5 m) where small children cannot
reach, away from moving parts of door and door
hardware. If installing into drywall, drill 5/32" holes and
use the anchors provided. For
pre-wired installations (as in new home construction), it
may be mounted to a single gang box (Figure 2).
1. Strip 7/16" (11 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back
of door control by color: white wire to 2 and white/red
wire to the 1.
2. Door Control Button: Fasten securely with
6ABx1-1/2" screws.
Console Model: Remove cover by gently prying along
one side with a screwdriver (Figure 1). Fasten with
6ABx1-1/4" self-tapping screws (drywall installation) or
6-32x1" machine screws (into gang box) as follows:
• Install bottom screw, allowing 1/8" (3 mm) to protrude
above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid cracking
plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up wall
and across ceiling to motor unit. Use insulated staples
to secure wire in several places. Do not pierce wire
with a staple, creating a short or open circuit.
4. Strip 7/16" (11 mm) of insulation from end of bell wire.
Connect bell wire to the quick-connect terminals as
follows: white to white and white/red to red.
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires
into quick-connect holes: white to white and red/white
to red.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
and manual release/safety reverse test label in
a prominent location on inside of garage door.
NOTE: DO NOT connect power and operate
opener at this time. The trolley will travel to the
full open position but will not return to the close
position until the sensor beam is connected and
properly aligned.
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing door
control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a
closing garage door:
• Install door control within sight of garage door, out of reach
of children at a minimum height of 5 feet (1.5 m), and away
from all moving parts of door.
• NEVER permit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed.
NEVER permit anyone to cross path of closing garage door.
To opener quick-connect terminals: white to white;
white/red to red.
Figure 1
REMOVE & REPLACE COVER
To Replace,
Insert
Top Tabs
First
Lighted
Push Button
DOOR
CONTROL
STANDARD
BUTTON
CONTROL CONSOLE
Door Control
Connections
Strip wire 7/16" (11 mm)
7/16" (11 mm)
Red
17
WARNING
WARNING
Outside Keylock Accessory Connections
Screw 6ABx1-1/2"
Door Control Button
Screw 6ABx1-1/4"
Control Console (std installation)
Screw 6-32x1"
Control Console (pre-wired)
To Remove,
Twist
Here
Quick-Connect
Terminals
2-Conductor
Bell Wire
To release wire, push in
tab with screwdriver tip
Antenna
White Grey
HARDWARE SHOWN
ACTUAL SIZE
Insulated
Staples
Drywall Anchors
Figure 2
PRE-WIRED
INSTALLATION
24 Volt
2-Conductor
Bell Wire
DOOR CONTROL
BUTTON (BACK VIEW)
Bell
Wire
Terminal Screws
STANDARD CONTROL
(BACK VIEW)
Top
Mounting
Hole
RED
WHITE
2 1 Terminal
Screws
Bottom
Bell Mounting
Hole
Wire