Bort TITAN 4000 Mode D'emploi page 13

(wall) switch or a pneumatic switch .
Wireless (wall) switch
The disposer of the "Control and FullControl"
series are equipped with a wireless wall mount
switch .
The switch should be located in a convenient
(safe for children) place above the table top .
For instal the switch to the wall, use double-
sided tape .
For activate / deactivate the device, hold down
the key for 2-3 seconds .
Battery type: Voltage: 12V; Size: A27
Air switch
Disposer is equipped with an air switch and a
connecting pipe (except "Control" series).
INSTALLATION OF AIR SWITCH
1 . Drill a hole with a diameter of 32 mm in
suitable top or top the panel of a sink . Some
sinks may already have a suitable A hole for the
opening of which is necessary remove the cover .
2 . Unscrew the nut from the body of the push
button, while holding the stainless steel washer
and rubber gasket in place . Place one end of the
PVC tube on the spout on the body Press the
other end to A hole in the table top and a nut
located under the countertop . (Fig . 10 .2)
3 . Place the push button housing in the hole and
tighten the nut underneath countertop (enough
arm effort) . Do not use the key to tighten nut .
(Fig . 10 .3)
4 . Take the other end of the duct and tightly put
it on the spout of the air switch located on the
bottom of the disposer . (Fig .10 .4) Hand tighten
the clamping nut . The disposer installation is
complete . Before using the product, read all of
the instructions . operation and safety contained
in paragraph 10 of this manual . In conclusion,
install the plug in the sink in the Closed position .
Fill the sink with water, Remove the plug and
check the connections on the a water leakage .
Wireess button
To connect the wireless button, install the power
supply into an electrical outlet, then insert the
chopper plug into the power supply (Fig .10 .1)
The power supply
are synchronized at the factory, so no
additional configuration
If the power supply and the power button are out
of sync, they should be rewritten . To do this, hold
down the button on the power supply for more
than 5 seconds until the LED indicator flashes
- the power supply has switched to recording
mode .
and the power
is required.
Then press the power key 3-5 times . The power
key is written . Recording mode will automatically
turn off after 1 minute .
10. ATTENTION! IMPORTANT INSTRUCTIONS
FOR
SAFETY
• If the air switch does not work, remove the plug
power supply from the outlet and check the air
duct pneumatic switch and delivered to the outlet
electricity .
• This product is designed for grinding food residues
at home; the ingress of substances other than food
into the disposer may cause injury and / or damage
property . To reduce the risk of Do not use a washer
with an installed disposer not for food purposes (for
example, for bathing a child or washing your head) .
• Children should be supervised adults and should
not play with a disposer . To reduce the risk of injury
It is necessary to keep a watchful eye on children
use of the product .
• If the wedging in the disposer is eliminated,
turn off the appliance and disconnect it from the
electrical network . Use a wrench for self-removal
of jammed waste according to description in the
section "Elimination of jamming disposer ".
• Use tongs or pliers to remove foreign objects from
the product .
• To reduce the risk of injury from particles that are
thrown out by the disposer, it is prohibited to use
grinders withoutnoise shielding screen (Fig .8 .3) .
Place the plug in the drain hole, as shown in Fig .
11 .2 or 11 .4 .
Do not allow the following items to fall into the
disposer: shells, including oyster, caustic means for
cleaning pipes or similar chemical products, glass,
porcelain or plastic, large (hollow) bones, metal
objects (bottle caps, cans, or kitchen appliances),
hot fat or other hot liquids .
• Replace worn noise glossy screen / installation
gasket / protective reflector if they are worn and are
no longer able to prevent waste or water .
• If the disposer is switched off, use a stopper to
prevent foreign objects in the grinding camera .
Make sure that the power of the disposer is
disabled .
• Before pressing the reset button, cleaning the jam
key
or removing foreign objects from the shredding
chamber, make sure that the food is turned off .
• Keep hands and fingers out of the reach of
disposer chamber .
FIRE RISK:
To minimize the possibility of Do not store near
fire extinguishing articles such as rags, paper or
aerosol cans . Do not store or use gasoline or other
13