Télécharger Imprimer la page

Bort TITAN 4000 Mode D'emploi page 12

Masquer les pouces Voir aussi pour TITAN 4000:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 15
in the horizontal part of the drainage pipes,
moving with side of the siphon towards the main
pipe .
IF THE DISHWASHER WILL NOT BE CONNECTED
TO THE DISPOSER, GO TO PART 7 OF THIS
INSTRUCTION
6. CONNECTING THE DISHWASHER
MACHINES AND TRANSFER CONNECTION
To connect the dishwasher, you should use the
input hole in the top of the disposer (Fig . 7 .2) .
To connect, remove the barrier (Fig . 7 .1) .
If the sink is overfilled with liquid, then it should
be connected through the inlet in its upper part
of the drain pipe (Fig . 7 .2) .
!!!
On
some
a
barrier
inside
parent to be removed .
REMOVING THE PLATE / PARTITION
1 . Place the disposer on one side and place
it screwdriver into the connection for the
dishwasher, pushing it until it will not rest against
the partition in the end of the branch pipe .
2 . With several blows of the hammer, knock out
the septum in the branch pipe (Fig . 7 .1) .
3 . Remove the embossed partition from the
disposer bowl . If necessary to connect the
dishwasher, then it should be connected to the
inlet of the overflow outlet pipes To connect to
the overflow inlet, remove the exhaust pipe cover
by unscrewing the cover (Fig . 7 .3) .
7. CONNECTING THE DISPOSER TO THE FIXING
UNIT ATTENTION!
To avoid injury, follow the so that during the
removal and installation of a part Your body was
not under the disposer; during the installation it
is possible to drop it .
Remove any objects from the grinding chamber
product before installing it on the sink .
1 . Install the product in such a way that provide
easy access to the restart button engine located
in the lower part of the body . Do not block this
place with any objects .
2 . Place the disposer with three mounting loops
(1) into the sliding position by mounting rails (2) .
(Fig .8 .1)
3 . Lift the disposer, insert the top end (installation
gasket) in the mounting and turn the setting
ring to the right (with a wrench or adjustable
pliers) until the mounting loops are fixed (3) with
respect to the mounting rails (Fig . 8 .2) .
Make sure that all three mounting loops are
locked . Disposer is installed .
4 . Run water into the sink, then check the
models,
there
the
drain
pipe
connections for leaks .
5 . Insert the noise absorbing screen into the
drain hole flat side up. (Fig.8.3)
8. CONNECTING THE OUTLET PIPE
To the DRAIN PIPE ATTENTION!
• It is recommended to wear protective goggles
when installing the disposer .
• For all models, the drain pipe is connected
using a screw connection (Fig . 9 .1) .
• Use a sanitary sealant only for connecting the
flange of the sink with the disposer.
Do not use sealants for threaded pipe
connections or anaerobic screwed sealants .
They can damage the product .
is
• Regularly check the disposer and fittings
for water leaks, since leaks water can cause
damage to property .
The manufacturer is not responsible for damage
to property as a result of water leaks .
INSTALLING THE DRAINAGE SYSTEM
1. Put the flange (2) on the drain pipe Insert the
rubber seal (1) . Fasten drain tube, tightly pulling
it to the body disposer with screws (4) . (Fig . 9 .1)
9. CONNECTING THE DISPOSER TO THE ELEC-
TRICAL NETWORK
ATTENTION! ELECTRIC SHOCK CURRENT
• To prevent electric shock, turn off the power
before installing or servicing the product .
• If you are not qualified enough, call an
electrician to connect the product to the power .
• If a three-pin grounding-type plug is used to
connect a three-contact outlet with ground .
• Do not modify the design of the plug supplied
with the device .
• Improper equipment grounding may cause
electric shock current .
• All electrical connections must comply with the
electrical and norms .
• Do not connect the ground to the feed pipe gas .
• Do not power on the distribution shield until
you have installed the sockets with proper
grounding .
• If the power cord is damaged, it must be
replaced at the service center .
NOTE: Access to a grounded outlet is required .
Installing all additional outlets must be carried
out by a qualified electrician, and all outlets must
be properly grounded .
Turn ON/OFF device
Depending on the models BORT disposer are
equipped with two types of control: a wireless
12

Publicité

loading

Produits Connexes pour Bort TITAN 4000