Télécharger Imprimer la page

Bort TITAN 4000 Mode D'emploi page 11

Masquer les pouces Voir aussi pour TITAN 4000:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 15
GB
ENGLISH
INSTALLATION
MAINTENANCE AND USING THE DISPOSER
Before installing the product, read everything
carefully . Installation, maintenance and use
manual . Before starting work determine which
tools, materials, and equipment you need .
Before installing the disposer, make sure that
you have all the necessary parts of the product .
REQUIRED TOOLS AND MATERIALS:
screwdriver, Hinged pliers, insulation tape, pro-
tective glasses
REQUIRED INSTRUMENTS, MATERIALS AND
OPTIONAL EQUIPMENT:
a Phillips screwdriver, a drainage drill, electrical
terminal 9 .5 mm, threaded nuts (2), siphon
38 mm, drill 32 mm, hammer, hacksaw, water
hose clamp, pipe pliers, copper grounding wire,
dishwasher drainage pipe kit, electric switch,
extension pipe
1. DESCRIPTION OF THE PRODUCT (FIG.1.1)
Assembly unit
1 . Stopper;
2. Washing flange;
3 . Rubber gaskets (2);
4 . Support ring;
5 . Mounting ring;
6 . Screws;
7 . Locking ring;
8 . Sound attenuating screen;
Disposer
9. Installation gasket / protective reflector;
10 . Eyelets;
11 . Lower mounting ring;
12 . Drain the dishwasher;
13 . Outlet opening;
Drainage system
14 . Mounting Screws;
15 . Rubber gasket;
16 . Flange;
17 . Drain pipe with a knee .
2. DISCONNECTION OF THE DROP HORN AT-
TENTION!
At the time of installation of the device is
recommended Wear safety glasses . Loosen the
nut (1) on the top of the water trap (4) with a pipe
wrench (Fig . 3 .1) . relative humidity not more
INSTRUCTIONS,
11
than 80% . Loosen the nut (2) on the top of the
extension pipe . Remove the extension pipe .
Loosen the nut (3) at the bottom of the washing
flange.
Push the washing flange upwards through drain
hole of the sink and remove it (Fig . 3 .2) .
CLEAN THE WASH FAN WRAPPING PLACE
FROM THE SEALANT OR THE GARBAGE .
NOTE: It may be necessary to expand the drain
hole for installation flange fastening disposer.
Equipment for extending the drainage hole is
purchased separately .
3. DISASSEMBLY OF THE ASSEMBLY UNIT
• Turn over the assembly (Fig .4 .1) and loosen the
three fixing screws (1) The access to the ring (2).
• Disconnect the retaining ring from the flange
with a screwdriver . Now the assembly unit can
be disassembled .
4. ATTACHING THE FIXING ASSEMBLY TO
WASHING Fig.5.1.
ATTENTION! To install the disposer, the thick-
ness of the sink in the area of the drain hole
should be no more than 18 mm .
1 . Install one or two rubber gaskets (2) under the
washing flange (1). Make sure that The drainage
hole is not clogged, and set to flange washer /
gasket. In order to The flange of the sink became
in place, you need to crush it with a heavy load .
(To avoid scratches, use a towel as a lining .)
2 . Put the second rubber part on the bottom of
the kitchen sink a gasket (2), a cardboard gasket
(optional) (3) and a metal support ring (4) (flat
side up) .
3 . While holding the second rubber gasket,
cardboard padding (optional) and a metal
support ring, put the mounting ring (5) on the
flange of the sink so that it aligned with the
support ring .
4 . Pressing tightly to the bottom of the sink
rubber gasket, cardboard gasket, support ring
and mounting ring, slide the snap ring (7) onto
the flange of the sink so that it snaps into the
flange groove.
5. Tighten the three fixing screws (6) to The
fixing assembly was tight and evenly pressed to
the sink .
5. CLEANING THE DRAIN PIPE
If you do not clean the drain pipe, it can clog .
1 . Remove the water trap . (Fig .6 .1)
2 . Using a cleaner, remove all solid precipitation

Publicité

loading

Produits Connexes pour Bort TITAN 4000