Milwaukee AG 750-115 Notice Originale page 18

TECHNICAL DATA
Rated input ..................................................................................
Max. no-load speed .....................................................................
Grinding disk diameter.................................................................
Thread of work spindle ...............................................................
Weight according EPTA-Procedure 01/2003 ...............................
Noise/Vibration Information
Measured values determined according to EN 60745.Typically,
the A-weighted noise levels of the
tool are:
Sound pressure level (K = 3 dB(A)) ...........................................
Sound power level (K = 3 dB(A)) ...............................................
Wear ear protection!
Total vibration values (vector sum in the three axes) determined
according to EN 60745:
Surface grinding: vibration emission value a
Uncertainty K = ............................................................................
Disk sanding vibration emission value a
Uncertainty K = ............................................................................
For other applications, e.g. Abrasive Cutting-Off Operations or
Wire Brushing other vibration values could occure.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions may
result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush, or cut-off tool. Read all safety
warnings, instructions, illustrations and specifi cations
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fi re and/or
serious injury.
b) Operations as polishing are not recommended to be
performed with this power tool. Operations for which the
power tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not specifi cally
designed and recommended by the tool manufacturer. Just
because the accessory can be attached to your power tool, it
does not assure safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can break
and fl y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
f) The arbour size of wheels, fl anges, backing pads or any
other accessory must properly fi t the spindle of the power
tool. Accessories with arbour holes that do not match the
mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear,
18 ENGLISH
414 032 - AG750-115.indd 18 414 032 - AG750-115.indd 18
Angle Grinder
AG 750-115
220 V - 240 V
....... 750 W ................. 750 W ................. 750 W ..............750 W
... 10000 (min
....... 115 mm .............. 125 mm ............... 115 mm ...........125 mm
..... M 14 .................. M 14 ................... M 14 ...............M 14
........ 1,8 kg ................. 1,8 kg .................. 1,8 kg ..............1,8 kg
...... 87,1 dB(A) .......... 83,5 dB(A) ......... 87,1 dB(A) .......83,5 dB(A)
...... 98,1 dB(A) .......... 94,5 dB(A) ......... 98,1 dB(A) .......94,5 dB(A)
............................. ........ 6,8 m/s
h
........ 1,5 m/s
.................................... ........ 3,5 m/s
h
........ 1,5 m/s
wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an
undamaged accessory. After inspecting and installing an
accessory, position yourself and bystanders away from
the plane of the rotating accessory and run the power tool
at maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping
small abrasive or workpiece fragments. The eye protection
must be capable of stopping fl ying debris generated by various
operations. The dust mask or respirator must be capable of
fi ltrating particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal protective
equipment. Fragments of workpiece or of a broken accessory
may fl y away and cause injury beyond immediate area of
operation.
j) Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a „live" wire may make exposed
metal parts of the power tool „live" and shock the operator.
k) Position the cord clear of the spinning accessory. If you
lose control, the cord may be cut or snagged and your hand or
arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may grab
the surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
n) Regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical hazards.
AG750-115 AG 750-125
110 V 220 V - 240 V
) ...... 10000 (min )....... 10000 (min
-1 -1
.............. 5,7 m/s ............... 6,8 m/s
2 2
.............. 1,5 m/s ............... 1,5 m/s
2 2
........... < 2,5 m/s ............... 3,5 m/s
2 2
2 .............. 1,5 m/s 2 ............... 1,5 m/s
AG750-125
110 V
) ...10000 (min )
-1 -1
...........5,7 m/s
2 2
...........1,5 m/s
2 2
........< 2,5 m/s
2 2
2 ...........1,5 m/s 2
09.10.2012 17:09:44 09.10.2012 17:09:44