Publicité
&WARNING
•
If you connect the ignition wire (Red) to the car
chassis (Ground), you may cause a short circuit,
that
in turn may start
a fire.
Always connect those wires
to the
power
source
running through the fuse
box.
•
Do
not
cut out the fuse from
the ignition
wire (Red).
The power
supply must be connected to the wires
via tf-le fuse.
&CAUTION
•
If your car's ignition does not
have
an ACC position,
connect the ignition wires to a power source that
can be turned on and off with
the ignition key. If
you
connect the
ignition
wire
to
a power source with a
constant voltage supply, as with battery wires, the
battery
may
die.
•
If
the fuse blows,
first make sure the wires aren't
touching
to
cause a short circuit,
then replace
the
old fuse with one with the same rating.
•
Insulate unconnected wires with vinyl tape or other
similar material.
To
prevent a short circuit,
do
not
remove
the caps on
the
ends of
the
unconnected
wires or the terminals.
•
After the
unit is
installed, check whether the brake
lamps,
blinkers, wipers, etc. on
the
car are working
properly.
Install so that
it
does
not
obstruct the
rear
field of
view.
•
Install so that it does not
protrude
from the side of
the car.
•
Do
not
perform installation in rain or fog.
•
When
humidity
is high, dry the surface to which the
unit
is
to be attached before installing.
•
Moisture on
the
attachment surface
reduces
adhesive strength, which may
lead to
the unit
coming
off.
•
Do not attach
the
camera
bracket
to areas on
the
car
body treated with fluorocarbon
resin,
or glass.
•
May result in
the rear
view camera falling off.
- Do not apply water to the
unit.
- Do
not
expose the unit
to rain.
- Do not subject the camera to unnecessary force.
- Thoroughly clean where tape
is
used for sticking
on the
unit.
•
Refer
to
the
Instruction's
manual for details on
connecting
the
other
units,
then make connections
correctly.
•
Secure
the
wiring with
cable
clamps or adhesive
tape. To
protect
the wiring, wrap adhesive tape
around them where they lie against metal parts.
•
Route and secure all wiring so it cannot touch any
moving parts, such as
the
gear shift, handbrake and
seat rails.
•
Do not route wiring in
places
that get hot, such as
near the heater outlet. If the insulation of the wiring
melts or gets
torn,
there is a danger of the wiring
short-circuiting to the vehicle body.
•
When replacing the fuse, be sure
to
use"only fuse of
the
rating
prescribed
on the fuse holder.
•
To
minimize noise locate the TV antenna cable, radio
antenna cable and
RCA
cable as far away from each
other as possible.
•
Lay the cords by avoiding high-temperature areas.
Use corrugated tubes for wiring inside
the
engine
room. If a cord contacts a high-temperature area of
the vehicle, the coating may melt and cause short-
circuiting, which may lead to a fire or electric shock
hazard.
Accessories
Camera (3.0 m) ..........
1
Power cord (6.0 mlll)
..........
l
Powerunit...
.......
l
Camera bracket...
....... l
I:)
Screw (M3
x
5 mm) .......... 2
Camera bracket clamping screw
(03
x
8
mm)
..........
1
~
~
Grommet..
........
l
Band
.......... 1
[1] Including the
power
unit
English
5
Publicité
