Télécharger Imprimer la page

Bosch 0.601.B19.200 Notice Originale page 33

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 38
Bevel angle
Mitre angle
0°–47°
≤ 44°
(left)
(right/left)
0°–47°
≥ 45°
(left)
(right/left)
0°–47°
≤ 44°
(right)
(right/left)
0°–47°
≥ 45°
(right)
(right/left)
Clamping the Workpiece (see figure G)
To ensure maximum safety while working, the workpiece
must always be firmly clamped.
Do not saw workpieces that are too small to clamp firmly.
– Press the workpiece firmly against the fences (15)
and (14).
– Insert the supplied screw clamp (28) into one of the cor-
responding holes (35).
– Adjust the threaded rod (52) of the screw clamp to the
workpiece height.
– Tighten the threaded rod (52) to fix the workpiece in
place.
Setting mitre and bevel angles
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
Always tighten the locking knob (21) and the clamp-
u
ing lever  (41) firmly before sawing. Otherwise the saw
blade can become wedged in the workpiece.
Note for adjusting mitre angles > 45°:
Before adjusting the mitre angle, pull the saw table
extension (13) and the adjustable fence (15) all the way
out.
For bevel cuts when using the SDS bolt (50), before
u
sawing, first make sure that the SDS bolt cannot come
into contact with the surface of the workpiece at any
time by making a suitable adjustment to the depth
stop (32). This prevents damage to the SDS bolt and/or
the workpiece.
Setting Standard Mitre Angles (see figure H)
For quick and precise setting of commonly used mitre
angles, detents (25) are provided on the saw table:
Leftward
45°; 31.6°; 22.5°; 15°
– Loosen the locking knob (21) if it is tightened.
Bosch Power Tools
– Loosen the locking screw (51).
– Pull the left-hand adjustable fence (15) all the way out.
– Loosen the locking screw (51).
– Pull the left-hand adjustable fence (15) all the way out.
– Lift the adjustable fence upwards and out of the way.
– Remove the locking screw (51).
– Loosen the locking screw (51).
– Pull the right-hand adjustable fence (15) all the way out.
– Lift the adjustable fence upwards and out of the way.
– Pull the lever (22) and rotate the saw table (16) left or
– Release the lever again. The lever must be felt to engage
– Retighten the locking knob (21).
Setting Any Mitre Angle (see figure I)
The mitre angle can be set between 52° (left side) and 60°
(right side).
– Loosen the locking knob (21) if it is tightened.
– Pull the lever (22) and at the same time press the locking
– Turn the saw table (16) left or right by the locking knob
– Retighten the locking knob (21).
– To loosen the lever (22) again (for setting standard mitre
Setting the Complete Bevel Angle Range (see figure J)
The bevel angle can be set between 47° (left side) and 47°
(right side).
– Pull the stop (44) all the way forward.
– Pull the right-hand adjustable fence (15) all the way out
– Loosen the clamping lever (41).
– Swivel the tool arm left or right by the handle (9) until the
Rightward
– Retighten the clamping lever (41).
Setting Standard Bevel Angles (see figure K)
15°; 22.5°; 31.6°; 45°; 60°
For quick and precise setting of frequently used bevel
angles, stops have been provided for the angles 0°, 45°,
22.5° and 33.9°.
right to the required detent.
in the detent.
clamp (20) until this clicks into the slot provided for it.
This means the saw table can now move freely.
until the angle indicator (24) shows the required mitre
angle.
angles), pull the lever upwards.
The locking clamp (20) springs back into its original posi-
tion and the lever (22) can click back into the detents
(25).
This enables you to use the complete bevel angle range
(left and right).
or remove it completely .
If you want to use the entire bevel angle range, you also
have to pull the left-hand adjustable fence (15) all the
way out or remove it completely.
angle indicator (42)/(31) shows the required bevel
angle.
1 609 92A 7NA | (26.04.2022)
English | 33

Publicité

loading

Ce manuel est également adapté pour:

Gcm 8 sde professional