Table des Matières
Publicité
3. Avec 6 boulons à bride hexagonal (D) et 6 contre-
écrous (E) pour bloquer les butées (C).
A
D
B
C
E
Pour assembler le rotateur de goulotte
1. Assembler l'extrémité avant du rotateur de goulotte.
2. Installer la bague en plastique (B) à l'extrémité avant
du rotateur de goulotte.
3. Fixer le rotateur de goulotte avec 1 entretoise
plat (A) et 1 goupille fendue (C).
C
A
B
4. Assembler l'extrémité arrière du rotateur de goulotte.
46
5. Utiliser 1 contre-écrou M8 (A), 1 poignée de
verrouillage en plastique (B), 2 entretoises de
courbe (C) et 1 niveau de vis (D) pour monter le
rotateur de goulotte.
6. Utiliser 1 écrou hexagonal M8 (E) pour fixer le
rotateur de goulotte (F) dans les trous de la poignée.
A
B C
C
E
F
D
Pour assembler la tige de commande
de vitesse d'entraînement
1. Installer la longue extrémité courbée de la tige de
commande de vitesse d'entraînement (A) sur le
panneau de commande, et fixez-la à l'aide d'un
ressort de tige de raccordement (B), 1 entretoise
plate (C) et 1 goupille fendue (D).
A
B C
D
621 - 005 - 31.05.2018
M M aintenance
Daily
20 hours
Inspect and
change the spark
plug
3
Note: It is not necessary to add grease or to do other
maintenance to the gearbox.
To do a general inspection
•
Make sure that the nuts and screws on the product
are tightened.
To do a check of the oil level
CAUTION: A too low oil level can do
damage to the engine. Do a check of the oil
level before you start the product.
1. Put the product on level ground.
2. Remove the oil tank cap with the attached dipstick.
3. Clean the oil from the dipstick.
4. Put the dipstick fully into the oil tank to give a correct
picture of the oil level.
5. Remove the dipstick.
6. Examine the oil level on the dipstick.
7. If the oil level is low, fill with engine oil and do a
check of the oil level again.
To replace the engine oil
1. Run the engine a few minutes to make the oil warm.
Warm oil flows better and carries more
contaminants.
WARNING: The engine oil is hot. Avoid
skin contact with the used engine oil.
2. Put the product on level ground.
3. Run the engine until all fuel has been depleted.
4. Remove the ignition key.
5. Put a container under the oil drain plug.
3
Check and clean spark plug before use each year.
621 - 005 - 31.05.2018
50 hours
100 hours
150 hours
X
6. Remove the oil drain plug, tip the product backwards
and drain the used oil in the container.
7. Put the product back to the operating position.
8. Fit the oil drain plug and tighten it securely by hand.
9. Fill the engine with oil, see
To fill the engine with oil
on page 9 .
To examine the spark plug
CAUTION: Always use the recommended
spark plug type. Incorrect spark plug type
can cause damage to the product.
•
Examine the spark plug if the engine is low on
power, is not easy to start or does not operate
correctly at idle speed.
•
To decrease the risk of unwanted material on the
spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
•
If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, see
Technical data on
page 19 .
•
Replace the spark plug if it is necessary.
15
Publicité
Table des Matières
