Publicité
Les langues disponibles
Les langues disponibles
NOTE:
• If you connect a Makita vacuum cleaner to your plate
joiner, more efficient and cleaner operations can be
performed.
OPERATION
How to make joints
WARNING:
• Always clamp the workpiece to the workbench before
each operation. (Fig. 14 & 15)
Corner Joint (Fig. 16, 17 & 18)
T-Butt Joint (Fig. 19, 20 & 21)
Miter Joint (Fig. 22 & 23)
Frame Joint (Fig. 24 & 25)
Edge-To-Edge Joint (Fig. 26 & 27)
To make joints, proceed as follows:
1.
Fit the two workpieces together as they will appear
in the finished joint position.
2.
Mark the center of the intended biscuit grooves on
the workpiece using a pencil.
NOTE:
• The center of grooves should be at least 50 mm from
the outer edge of the workpieces.
• Allow 100 mm – 150 mm between grooves in multiple
biscuit application.
3.
For Corner Joint and T-Butt Joint only
Clamp the vertical workpiece to the workbench.
For Miter Joint only
Clamp one workpiece to the workbench with the
mitered edge facing up.
For Frame Joint and Edge-To-Edge Joint only
Clamp one workpiece to the workbench.
4.
Set the depth of groove according to the size of bis-
cuit to be used. Refer to the table in the "Adjusting
the depth of groove" section.
5.
Adjust the angle guide height so that the blade is
centered in the board thickness.
6.
Align the center mark on the base with the pencil
line on the workpiece.
7.
Switch on the tool and gently push it forward to
extend the blade into the workpiece.
8.
Gently return the tool to the original position after the
adjusting screw reaches the stopper.
9.
For Corner Joint and T-Butt Joint only
Clamp the horizontal workpiece to the workbench.
For Miter Joint only
Clamp the other workpiece to the workbench with
the mitered edge facing up.
For Frame Joint and Edge-To-Edge Joint only
Clamp the other workpiece to the workbench.
10. For Corner Joint only
Place the tool on the workpiece so that the blade is
facing down.
For T-Butt Joint only
Remove the angle guide from the tool. Place the tool
on the workpiece so that the blade is facing down.
11. Repeat the steps 6 – 8 to groove in the horizontal or
the other workpiece.
If you do not need to center the blade in the board thick-
ness, proceed as follows:
For Corner Joint, Miter Joint, Frame Joint and
Edge-To-Edge Joint only
• Remove the angle guide from the tool. Set the
fence at 90° for Corner Joint, Frame Joint and
Edge-To-Edge Joint or at 45° for Miter Joint.
• Follow steps 1 – 11 excluding steps 5 and 10
described above.
For T-Butt Joint only
• Fit the two workpieces together as they will appear
in the finished joint position.
• Lay the vertical workpiece on the horizontal one.
Clamp both workpieces to the workbench.
• Remove the angle guide from the tool.
• Follow the steps 2, 4, 6, 7, 8 and 11 described
above.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
The tool and its air vents have to be kept clean. Regularly
clean the tool's air vents or whenever the vents start to
become obstructed. (Fig. 28)
Replacing carbon brushes
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes. (Fig. 29)
Insert the top end of slotted bit screwdriver into the notch
in the tool and remove the holder cap cover by lifting it
up. (Fig. 30)
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps. (Fig. 31)
Reinstall the holder cap cover on the tool.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Angle guide
• Dust bag
• Set plate
• Lock nut wrench
• Plate joiner blades
• Makita genuine battery and charger
9
Publicité
