Publicité
The product is not compatible with top connected
concrete chimney.
Requirements for Floor Plate by Combustible Floor
Follow the requirements for floor plate (stone, steel,
etc.) that apply in the country that the product is
installed in.
Glue
The outer elements should be glued with the acrylic
which is included. Make sure that all the surfaces that
are to be glued are free of dust. The surfaces can be
cleaned for better adhesion. Ensure that the surfaces
are dry before spreading on the acrylic. Once the
fireplace is assembled, fill the joints with acrylic and
even it out with a sponge or finger and some soapy
water, in order to have a clear indentation between the
elements (FIG Z).
Minor Dents
Transportation and handling can cause minor dents to
the product. This can be repaired with the powder glue
which is included. For a perfect result you can fill and
grind with a suitable filler on top of the powder glue.
Fill smaller cracks and uneven surfaces with a float or
a brush. If the dent is deep, it is recommended to fill in
several stages to avoid sinking. Even out with e.g. a
damp sponge or a float.
Painting
The surface of the chimney surround is developed to be
painted without priming work. Use latex or acrylic based
paint (emulsion paint), or cement-based textured paint.
In the unlikely case that there are some irregularities in
the surface, these can be filled with the acrylic which is
included, or a light and appropriate filling material. Any
surface that has been filled needs to be smoothened
with fine sand paper.
Polishing
If a more traditional and polished surface is wished for,
it is recommended to dampen the surround and then
cover it with tile adhesive (powder glue) and a fibreglass
mesh, prior to possibly adding mortar or mineral polish.
Tiles
This fireplace can also be partially or completely
covered with tiles / natural stone of your choice. As for
the section above on "Polishing", we recommend that
the chimney surround is dampened before it is covered
with tile adhesive (powder glue) and a fiberglass mesh.
This is to ensure good adhesion and prevent the
formation of cracks at the joints of the surround.
Maximum weight of steel chimney (top connection)
is 350kg.
By top connection to steel chimney, we refer to the
respective manufacturer's installation instructions.
Please note that the adhesive and mortar must
set before burning in the fireplace. Follow the
4
All manuals and user guides at all-guides.com
instructions from the mortar/adhesive producers.
Regardless of surface treatment it is advantageous to
mask the entire door frame to avoid having to clean it
later.
Please note that the air gap between the surround
and the door frame must not be filled with glue,
mortar or similar.
Thermotte™
The insulation plates (Thermotte) are classified as "wear
and tear" parts which will require to be exchanged after
some years.
The wear time will depend on the individual use of your
product.
Nordpeis offers a one-year warranty on these parts.
After this, replacements can be purchased.
Please note: Wood logs that are too long can cause
additional strain and crack the plates, due to the tension
created between the side plates.
Cracks in the i PowerStone
Due to thermal effects there may be small cracks /
fissures in the PowerStone. This is natural and does not
affect the product's function or safety.
2. Warranty
For detailed description of the warranty conditions see
the enclosed warranty card or visit our website
www.nordpeis.com
Recycling of the ceramic glass
Ceramic glass cannot be recycled. Old glass, breakage
or otherwise unusable ceramic glass, must be discarded
as residual waste. Ceramic glass has a higher melting
temperature, and can therefore not be recycled together
with glass. In case it would be mixed with ordinary
glass, it would damage the raw material and could, in
worst case end the recycling of glass. It is an important
contribution to the environment to ensure that ceramic
glass does not end up with the recycling of ordinary
glass.
GB
Warning!
Use replacement parts recommended only by
the Manufacturer.
Warning!
Any unauthorized modification of the appliance
without written permission of the Manufacturer
are prohibited.
Publicité
