EINHELL TE-MB 18/127 U Li Instructions D'origine page 27

handle (29) to pull out or push in the movable
clamping jaw (27).
•
Then swing the quick-adjust facility (30) back
down again in order to be able to clamp the
workpiece.
•
Clamp the workpiece by turning the handle
(29) clockwise.
•
Caution! Long workpieces must be secured
against falling off at the end of the cutting ope-
ration. You can use, for example, a roller stand
or similar.
6. Operation
6.1 Charging the Li battery pack (Fig. 13/14)
1. Remove the battery pack (6) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(7) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
Anl_TE-MB_18_127_U_Li_SPK13.indb 27 Anl_TE-MB_18_127_U_Li_SPK13.indb 27
GB
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Battery capacity indicator (Fig. 15/Item 9)
Press the battery capacity indicator switch (a).
The battery capacity indicator (9) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6.3 On/Off switch (Fig. 16)
•
Press the safety lock-off (5) in order to release
the On/Off switch (3).
•
Actuate the On/Off switch (3).
•
Important! You can let go of the safety lock-
off (5) as soon as the On/Off switch (3) was
actuated.
•
To switch off the saw, let go of the On/Off
switch (3) again.
6.4 Making cuts with the bandsaw in hand-
guided mode (Fig. 17)
•
The bandsaw is used without the base frame
(24). Remove the base frame (24) if necessa-
ry (see 5.6.1).
•
Set the adjustable handle (10) as described in
section 5.2.
•
Set the workpiece stop (13) as described in
section 5.3.
•
The material you want to cut must be clamped
securely.
•
Hold the machine firmly with both hands; use
the one hand on the handle (1) and the other
hand on the adjustable handle (10).
•
Take care to maintain a steady foothold.
- 27 -
01.02.2024 09:44:03 01.02.2024 09:44:03