EINHELL TE-MB 18/127 U Li Instructions D'origine page 23

transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Cordless bandsaw
•
Base frame
•
Blade
•
Additional blade
•
4 mm hex key
•
5 mm hex key
•
Original operating instructions
•
Safety instructions
3. Proper use
The cordless bandsaw is designed for cutting
non-alloyed steel (e.g. structural steel), non-
ferrous metal (e.g. aluminium), sawn timber and
wood-type materials. Alloyed steel, hardened
steel and tempered metals are not allowed to be
machined on this bandsaw. The cordless band-
saw is not designed for cutting fi rewood. No reac-
tive or poisonous materials are allowed to be pro-
cessed. Take care not to overload the machine.
The base frame is allowed to be used only with
the cordless bandsaw with which it is delivered.
Do not try to mount a diff erent electric tool on it.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
General safety information
It is the user's responsibility to install and use
the machine properly in accordance with the
instructions issued by the manufacturer. If elec-
tromagnetic interference is noticed, it is the user's
responsibility to eliminate said interference with
Anl_TE-MB_18_127_U_Li_SPK13.indb 23 Anl_TE-MB_18_127_U_Li_SPK13.indb 23
GB
the technical devices mentioned in the section
„Important information about the power connec-
tion".
Only blades suitable for the machine are allowed
to be used. To use the machine properly you must
also observe the safety information, the assembly
instructions and the operating instructions to be
found in these operating instructions.
All persons who operate and service the machine
must be acquainted with these instructions and
must be informed about potential hazards. It is
also imperative to observe the accident preven-
tion regulations in force in your area. The same
applies for the general rules of health and safety
at work.
The manufacturer will not be liable for any chan-
ges made to the machine nor for any damage
resulting from such changes.
Even when the machine is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards might arise in
connection with the machine's construction and
design:
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.
•
Risk of accident through hand contact with
the blade in the uncovered cutting zone.
•
Risk of injury when changing the blade (risk
of cuts).
•
Injuries from catapulted workpieces or parts
of workpieces.
•
Crushed fingers.
•
Injuries from kickback.
•
Tilting of the workpiece due to inadequate
support.
•
Touching the blade.
•
Dust and splinters can cause eye injuries. For
this reason you must always wear safety gog-
gles or spectacles with safety lenses.
•
Dust presents a special danger. You should
wear a suitable safety mask so that you are
not forced to breathe in any dust.
•
Always wear tight-fitting protective clothing
that is in perfect condition.
•
Long hair must be tied together, loose jewelry
should not be worn.
•
The workpiece you want to cut must always
be clamped securely. The workpiece must be
shaped so that it can be clamped securely.
- 23 -
01.02.2024 09:44:02 01.02.2024 09:44:02