EINHELL TE-MB 18/127 U Li Instructions D'origine page 25

•
Important! The two hex keys (22/23) are
stored in the adjustable handle (10) (see Fig.
2).
•
Important! Please note that the tooth pitch of
the blade you are using must match the mate-
rial you want to cut. In the case of particularly
hard materials or particularly large depths
of blade penetration you should change the
tooth pitch by changing the blade.
5.2 Adjusting the handle (Fig. 3)
•
The adjustable handle (10) can be fastened
in various locking positions according to re-
quirements.
•
Release the clamping lever (11).
•
Place the adjustable handle (10) in the requi-
red position.
•
Lock the setting by refastening the clamping
lever (11).
•
Important! You can adjust the pretension of
the clamping lever (11). To do so, hold the
released clamping lever (11) firmly and adjust
the nut (12) on the opposite side (clockwise:
higher tension). Check the setting by closing
the clamping lever (12) again. Keep repeating
until you have the required tension.
5.3 Adjusting the workpiece stop (Fig. 4)
•
Important! The workpiece stop (13) is set at
the factory to bottom position.
•
Caution! When you use the cordless bandsaw
together with the base frame (24), the workpi-
ece stop (13) must be set to bottom position.
•
Caution! When you work without the base
frame (24), the workpiece stop (13) should
also be set to bottom position because this
will increase the size of the guide face. Set
the workpiece stop to a higher position only in
exceptional cases.
•
Slacken the two socket head screws (14)
with the hex key (22) in order to be able to
push the workpiece stop (13) to the required
position. Then retighten the two socket head
screws (14).
5.4 Information about the LED lamp (Fig. 1)
•
The machine has an LED lamp (4) for illumi-
nating the cutting area.
•
As soon as you press the On/Off switch (3),
the LED lamp (4) will come on automatically.
•
A few seconds after you release the On/Off
switch (3) again, the LED lamp (4) will switch
off automatically.
Anl_TE-MB_18_127_U_Li_SPK13.indb 25 Anl_TE-MB_18_127_U_Li_SPK13.indb 25
GB
5.5 Fitting/removing the blade (Fig. 5 – 7)
Warning!
Before you start to fi t or remove the blade:
Remove the battery!
To prevent injury: wear gloves when chan-
ging the blade!
Fitting:
•
To be able to remove the left-hand blade co-
ver (36), slacken the socket head screw (40).
With the latching hook (37) pushed and held
in the up position, slide the blade cover (36)
outwards.
•
To be able to remove the right-hand blade
cover (38), slacken the socket head screw
(40). With the latching hook (39) pushed and
held in the up position, slide the blade cover
(38) outwards.
•
Before you mount the new blade, clean the
guide rollers (20) and the two blade pulleys
(18). Make sure in particular that the rubber
tire (19) is free of chips.
•
Caution! A damaged rubber tire (19) must be
replaced immediately.
•
To be able to fit the blade you must open the
clamping mechanism for the blade. Open the
clamping mechanism by turning the clamping
lever (16) clockwise (see Fig. 6).
•
To fit the blade: start at the bottom part of the
guide rollers (20), then continue around the
blade pulleys (18), and finish at the top part of
the blade guard (17).
•
Caution! Pay attention to the running direc-
tion. The cutting angle of the teeth must point
in running direction, i.e. towards the workpie-
ce stop (13). (See the arrow on the two blade
pulleys (18)).
•
Make sure that the new blade (15) runs freely
in the guide rollers (20) and in the upper bla-
de guard (17).
•
Tension the blade (15) by turning the clam-
ping lever (16) counter-clockwise.
•
Important! The blade must first be run in.
Switch on the machine briefly and check how
the blade is running. Check that the blade is
running correctly before you start cutting.
•
Refit the left-hand blade cover (36) and the
right-hand blade cover (38). Make sure that
both latching hooks (37, 39) latch home cor-
rectly. Fasten the two covers (36, 38) by tigh-
tening the socket head screws (40).
- 25 -
01.02.2024 09:44:02 01.02.2024 09:44:02