IKRA IES 1000 C Mode D'emploi page 27

f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe
handling and control of the tool in unexpected
situations.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety Instructions
A. General Instructions
1. Your electric tool is a high-speed, fast-cutting
power tool. The electrical connection and cutting
tool are potential sources of danger. Therefore,
special safety precautions must be observed to
reduce the risk of personal injury.
2. Always switch off the tool and disconnect the
plug from the power supply before carrying out
any maintenance or repair work on the unit.
Always unplug the tool if you leave it without
supervision.
3. Have your dealer or a specialist show you how to
operate your tool.
4. Minors should never be allowed to use an electric
lawn trimmer. Never lend or rent your electric
lawn trimmer without these operating instruc-
tions. Be sure that anyone using your tool un-
derstands the information contained in these
operating instructions.
5. The user is responsible for safety for all persons in
the working area of the device.
6. Never allow children or people unfamiliar with
the instruction to use the machine
7. Only use the machine in daylight or good artificial
light.
8. Before use the machine and after any impact,
check for signs of wear or damage and repair as
necessary
9. Never operate the machine with damaged guards
or without the guards in place.
10. You must be fit to operate an electric lawn trim-
mer- rested, healthy and in good physical condi-
tion. If you get tired while operating your scythe,
take a break. Never work with an electric lawn
trimmerwhile under the influence of alcohol or
drugs.
11. Never attempt to modify your tool. This excludes
all liability for personal injury or damage to prop-
erty caused by improper use or impermissible
modification.
GB | Operating Instructions
12. Do not use the tool if other persons, above all
13. The high-speed cutting head may catch and fling
B. Operational Precautions
14. Only use your lawn trimmerfor cutting grass and
C. Instructions regarding to safe handling
15. A power circuit breaker must be installed in the
16. Before starting work check that your electric tool
17. Before using the machine, the line and extension
18. If the cord is damaged during utilisation, it must
19. Attention! Danger. The cutting head continues to
20. The domestic mains voltage must match the
21. Only use extension cables that are intended for
22. Secure the extension cable in the cable strain
23. Do not use damaged power supply cords, exten-
24. Do not switch on the unit when hands or feet are
25. Any device that is used for cutting off the line
26. In spite of technical and additional protective
27. Keep handles dry and clean.
28. Remove foreign bodies from the working area.
29. Do not leave the machine unsupervised.
30. Comply with the accident prevention regulations.
31. Wear goggles or properly fitted safety glasses,
32. Careless use can cause injuries to hand and feet
GB-6
children, or animals are near the working area.
stones and other foreign objects a great distance.
To reduce the risk of injury, ensure that bystand-
ers / children and animals are at least 15 m (50 ft)
away from your own position.
weeds next to walls, under fences, around trees
and posts, on steps, garden paths and patios, un-
der bushes and hedges, on steep slopes, in gaps
between paving stones, etc.
power outlet to which the tool is connected or on
the electric cord to the tool. Contact an electrician
for further information. For a safe operation, it is
recommended to supply the machine over a fault
current safety breaker (RCD) with a fault current
not over 30 mA.
is in good condition and that it is operating prop-
erly. Pay special attention to the power supply
cord, extension cord, power outlet, switch and
cutting head.
cords have to be checked for signs of damage or
ageing. Do not use the tool when the cords are
damaged or worn.
be disconnected immediately from the mains.
DO NOT TOUCH THE CORD BEFORE IT IS DISCON-
NECTED FROM THE MAINS.
rotate after switch-off (flywheel effect). Keep your
fingers and feet well clear to avoid injury.
information relating to mains voltage in the tech-
nical data; do not use any other supply voltage
outdoor use – minimum cross section 1.5 mm 2 .
Always reel in cable drums fully.
relief.
sion cords, couplings, plugs or cut-ting heads.
near the cutting elements.
represents a danger of injury.
measures, there is always a residual risk when
working with the machine.
sturdy closed shoes with non-slip soles, snug-
fitting work clothes, gloves and ear protectors
(ear plugs or ear mufflers).