Attempting To Start; Removing The Power Pack; Using As A 12 V Voltage Supply; Using As A Usb Charger - APA BULLY SMART Manuel De L'opérateur

First connect the red (+) pole callipers (Position 1 in the over-
view) to the plus pole of your vehicle battery. The black (-) pole
callipers (Position 10 in the overview) is connected, as far as
possible from the battery, to the motor block or chassis (not
to a painted part).

6.6. ATTEMPTING TO START

Use the rotary switch (Position 2 in the overview) to switch on
the jump-start function. Start the motor. Do not operate the
starter for longer than 6 seconds. The battery of the power
pack is not designed for longer starting attempts. Pause for at
least 5 minutes between two starting attempts. If the motor
does not start after a number of attempts, abort the jump-
start process and investigate the cause of the defect.

6.7. REMOVING THE POWER PACK

Switch o the jump-start function with the rotary switch
(Position 2 in the overview). First disconnect the black (-) pole
calliper, coil the cable and attach the pole calliper to the de-
signated holder. Then disconnect the red (+) pole calliper, coil
the cable and attach the pole calliper to the designated holder.
Always maintain this sequence.
Recharge the power pack.

6.8. USING AS A 12 V VOLTAGE SUPPLY

The power pack can be used as a 12 V DC source for many
devices that can be operated with 12 V DC and a cigarette
lighter plug. Plug the cigarette lighter plug of the device you
wish to operated into one of the 12 V sockets (Position 5 in the
overview). The device you wish to operate should not require a
current greater than 10 A. The outlets of the power pack have
an automatic fuse that will deactivate the device at a current
greater than 10 A. If the unit is switched o , immediately dis-
connect the power pack from the device to be operated. After
approximately three minutes, the fuse will free the outlets for
use.
Calculation example for operating time as a direct
current source:
Battery capacity of the power pack: 18 Ah
Power consumption of the connected consumer (example):
2.5 A
18 Ah
____ = 7,2 h
2,5 A
Operating time/result: 7.2 h (hours)
(These values are, of course, only guidelines and refer to a
sound, completely charged battery.)

6.9. USING AS A USB CHARGER

You can also use the power pack as a USB charger. To do
this, connect your smartphone, MP3 player, etc. to the USB
output (Position 7 in the overview). Switch on the USB output
with the switch (Position 8 in the overview), the control light
below the USB output lights up. After charging, turn o the USB
output and remove your device from the USB output.

7. MAINTENANCE AND CARE

Maintenance: Store the power pack at room temperatu-
re. The battery will discharge even when not in use. If the
power pack is not used for a longer period of time, it must be
recharged for ve hours. In winter, recharge every six weeks, in
summer recharge every four weeks.
Care: Clean the housing of the power pack with a soft, dry
cloth. Do not use any aggressive cleaning agents or solvent-
based cleaners. Never allow liquids to ingress into the housing.

8. NOTES REGARDING ENVIRONMENTAL PROTECTION

Do not dispose of electrical devices with the
household waste! Electrical and electronic scrap
must be collected separately and disposed of in an
environmentally responsible manner for recycling.
Please contact your community or city administra-
tion regarding disposal options for electrical and
electronic scrap.
You are legally obliged to return batteries and
battery packs. After use, they may be returned to
us, handed in to a communal collection point, or
Pb
to a local dealer. Batteries containing hazardous
materials are labelled with a symbol consisting of
a crossed out trash can and the chemical symbol
(Cd, Hg or Pb) which designates the heavy metal
responsible for the hazard.

9. CONTACT INFORMATION

EAL GmbH
Otto-Hausmann-Ring 107
42115 Wuppertal, Germany
+49 (0)202 42 92 83 0
+49 (0) 202 42 92 83 – 160
info@eal-vertrieb.com
www.eal-vertrieb.com
7