Manual Operation (Cool, Dry, Heat); Air Flow Velocity And Direction Adjustment - Mitsubishi Electric MSZ-GA50VA Notice D'utilisation

MANUAL OPERATION (COOL, DRY, HEAT)

1
To select the COOL, DRY or HEAT/FAN mode:
Press the
2
Select the operation mode by pressing the
Each time this button is pressed, the operation mode is changed in sequence:
(AUTO) →
To stop operation:
I
Press the
After the operation mode is set once, the operation starts in the same mode as
the one set previously from the next time by simply pressing the
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
I
When the set temperature is to be changed:
TOO
WARM
• Press the button to lower the temperature. One press lowers the temperature by about 1°C.
TOO
COOL
• Press the button to raise the temperature. One press raises the temperature by about 1°C.
In COOL operation
• When the outside temperature is low, the fan of the outdoor unit turns on and off frequently or decreases the rotation
speed to maintain sufficient cooling capacity.
In DRY operation
• The temperature control (temperature setting) cannot be done.
• The room temperature is slightly lowered in this operation mode.
I
The details of the display on the indoor unit are explained on page 6.
If the air conditioner does not cool or heat effectively...
If the fan speed is set to Low or AUTO, sometimes the air conditioner may not cool or heat the air effectively. In this case,
change the fan speed to Med. or upper.
Fan speed: Low or AUTO
ON/OFF
button.
MODE
(COOL) → (DRY) →
(HEAT)
ON/OFF
button.
Change the fan speed.
Fan speed: Med. or upper

AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT

AIR FLOW velocity and direction can be selected as required.
button.
ON/OFF
button.
NOTE:
• In the cooling operation, when the air conditioner is operated with setting the horizontal vane to
1 hour, the AIR FLOW direction is automatically set to horizontal to prevent condensed water from dropping.
• Adjust the vertical AIR FLOW direction using the remote controller. If the horizontal vane is moved manually, it may
cause trouble.
• In the heating operation, if the air flow temperature is too low or when defrosting is being done, the horizontal vane
position is set to (1).
Auto air flow direction control operation
When the AUTO mode is selected with the
correspond to the operation mode for effective operation.
(1) HEAT: When the air flow temperature is too low, the air is blown out horizontally.
When the air flow temperature rises, the air is blown out downwards.
(2) COOL, DRY: The air is blown out horizontally.
I
To change the AIR FLOW blowing direction horizontally, press the
Each time the button is pressed, the angle of the VERTICAL VANE is changed in sequence:
→ →
SWING OPERATION
Use the swing operation for the air flow to reach all corners of the room.
Horizontal AIR FLOW blowing range
COOL/DRY
About 100°
About 150°
I
To change the AIR FLOW velocity, press the
Each time the button is pressed, the fan speed is changed in sequence:
(Low) → (Med.) → (High) →
• Use the (High) notch to cool/heat the room more.
• If the operating sound of the air conditioner disturbs your sleep, use the
(Low) notch.
I
To change the AIR FLOW blowing direction vertically, press the
VANE
button.
Each time the button is pressed, the angle of the horizontal vane is changed in
(1) → (2) → (3) →
sequence:
SWING OPERATION
Use the swing operation for the air flow to reach all corners of the room.
Recommended horizontal vane range
Use the (AUTO) position usually.
Use position (1) or (2) in the COOL or DRY mode
and use positions (3) to (5) in the HEAT mode
when adjusting to your requirements.
VANE
button, the position of the horizontal vane is automatically set to
→ → (SWING) → →
NOTE:
Adjust the horizontal AIR FLOW direction using the re-
mote controller. If the VERTICAL VANE is moved manu-
ally, it may cause trouble.
HEAT
FAN
button.
(AUTO)
(4) → (5) → (SWING) →
(AUTO)
1
COOL
2
DRY
3
HEAT 4
5
(4) or (5) for
WIDE VANE
button.
7