Enduro EM313 Manuel De L'utilisateur page 39

OPERATION – REMOTE HANDSET
The remote handset (9) is powered by 3x AAA 1.5 Volt batteries, and is activated by moving the slide switch to
"On"-I (Fig. 8A). Once activated the communication icon (Fig. 8H) will illuminate and the directional controls
can now be used.
Figure 8
A. Slide switch: "Off" –O and "On"-I
B. Caravan forwards: both wheels rotate in forwards direction
C. Caravan reverse: both wheels rotate in reverse direction
D. Caravan left forwards: right wheel rotates in forwards direction
E. Caravan right forwards: left wheel rotates in forwards direction
F. Caravan left reverse: right wheel rotates in reverse direction
G. Caravan right reverse: left wheel rotates in reverse direction
H. Communication icon: reflects communication status of the remote handset and caravan manoeuvring
system
I. Overload icon: Amp overload protection is activated. Wait about 60 seconds and try again.
J. Remote battery icon: The internal 1.5 Volt batteries of remote handset are near empty and need to be
replaced
K. Caravan battery icon : Caravan battery voltage too low or too high
When you drive straight forwards or reverse (press button B or C), it is also possible to adjust the direction by
additional pressing button D or E (when driving forwards) or button F or G (when driving reverse).
In addition, the 'right forward' (E) and 'left reverse' (F) buttons or 'left forward' (D) and 'right reverse' (G)
buttons may be pressed at the same time to turn the caravan around on its own axis without moving forward or
backward (this function just can work under the "single-axle function").
When you switch within 2 seconds from forward driving to reverse driving (and the other way around), a small
delay of 1 second will appear to protect the electronics and the motors.
The slide switch (Fig. 8A) also acts as an "Emergency stop".
The remote hand set switches off:
 After 3 minutes, if no button is pressed: After 2 minutes the buzzer will beep for 5 times with a repetition
after 3 minutes. Than the system switches in the "stand-by" modes.
 After 6 minutes, if one of the movement buttons is permanently held down: After 5 minutes the buzzer will
beep for 5 times with a repetition after 6 minutes. Than the system switches in the "stand-by" modes.
The screen goes off and the remote handset is in the "stand-by" mode which means that there always will be
used some current which causes the battery to go down. So always make sure the remote handset is turned off
by the slide switch.
To reactivate the remote handset, move slide switch to "Off" –O and then back to "On"-I after approximately 1
second.
Error messages via the remote handset:
Error messages of the EN
icon (Fig. 8H), the error message icons (Fig. 8I, J, K) and a buzzer signal:
 Communication icon (Fig. 8H) off, no buzzer: remote handset is turned off and also system is not activated
 Communication icon (Fig. 8H) continue on, no buzzer: remote handset is turned on and system is activated
and ready to use.
 Communication icon (Fig. 8H) is blinking, no buzzer: no communication between remote handset and
control unit. This could be because of too much distance between remote handset and control unit, or the
battery isolation switch for manoeuvring system is not turned on or that there is a distortion signal
disturbing the communication. As soon as connection is good again the communication icon will be
continue on and the system is ready to use.
 Caravan battery icon (Fig. 8K) is blinking in combination with buzzer (2 times blinking, break, 2 times
blinking, break etc.): Battery voltage too low (<10 Volt). Battery needs to be recharged.
 Caravan battery icon (Fig. 8K) is blinking in combination with buzzer (4 times blinking, break, 4 times
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on a
user (for example a lamp or water-pump).
 Overload icon (Fig. 8I) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
 Remote batteries icon (Fig. 8J) is blinking, no buzzer: The 3x AAA 1.5 Volt batteries are near empty and
need to be replaced.
® EM313 will be communicated via the remote handset by the communication
DURO
EN
DURO
® EM313 32
Ref: EM313-UM-TKI-0823-Rev.C.