Publicité
Les langues disponibles
Les langues disponibles
Getting Started: Initial Operation
Unpacking the Model
Remove the styrofoam packaging
extremely carefully to prevent
damaging accessories and attached
parts such as handrails etc.
Initial Operation
We recommend letting the locomotive
run without a train for 30 minutes
in both directions, to properly break
it in. This will help achieve optimal
performance and longevity for the
locomotive. Of course, your model
should only be run on smooth and
perfectly clean tracks with reliable
electrical contact to all track sections.
Technical Data
Power Supply
The model should only be operated
on a pure, filtered DC power supply
of 0 to 24 volts, with a capacity of at
least 2 Amp and a fast-acting fuse or
circuit breaker to protect against short
circuits. Do not use a power supply
which is not in safe and perfect
working condition. (See "Digital
Decoder" section for operation on
digital power.)
Mechanism
The locomotive has a powerful high-
precision motor, which turns the
wheels through a robust gearbox.
Lighting
The model is equipped with automatic
directional headlights, using white
LEDs for a realistic appearance.
The "front" lights are illuminated
according to the travel direction.
Radius
The locomotive can run on a track with
a minimum recommended radius of
600 mm (23.62'').
Digital Decoder
The model locomotive is prepared for
"plug and play" installation of a PIKO
#36125 Decoder (available separately).
As soon as the decoder is properly
installed, the locomotive can be
operated on digital as well as Analog
DC-powered layouts.
Sound Module
Only the model of the V 60 is prepared
for "plug and play" installation of a PIKO
#36195 Sound Unit (available separately).
This reproduces authentic sounds of the
real V 60. It requires that the loco be
equipped with a PIKO #36125 decoder.
The sound unit must be connected to the
decoder via the included interface cable.
The sound unit includes a high-quality
extended frequency range speaker with
a waterproof diaphragm for outdoor
operation. Note: The sound unit is
operable only on digital layouts, not
on analog DC-powered layouts.
Maintenance
Lubrication
After each 25 hours of operation, and
after any long periods of storage, please
lubricate the locomotive's gears with a
sparing amount of plastic-compatible,
non-hardening grease. Remove the
gearbox bottom cover and be careful to
keep the front and rear wheelsets aligned
with each other. Be sure to securely
re-tighten the gearbox bottom cover
screws.
Cleaning
If cleaning is necessary, use only a mild
cleaning agent (such as soap and water)
and gentle action with a soft non-
abrasive cloth or brush. Never immerse
the loco in liquid or "flood" any internal
parts!
Wheel Wipers and pick-Up shoes should
be changed after 500 hours of operation.
Please Note! Damage to Carpets
and Other Surfaces: Normal
operation of the locomotive causes
wear of mechanical parts (wheels,
electrical pickups etc.). This produces
carbonized dust, grease and oil,
which can permanently stain carpets,
wood floors and other materials. It
is the user's responsibility to take
proper precautions against this
damage. Wipe any grease or oil from
the track rails with a clean soft cloth.
PIKO Spielwaren GmbH, as well as
its representatives, distributors and
retailers, assume no liability for any
such damage.
Please Note!
Important Safety Precautions
• Check the power supply regularly for any
damage or problems.
• Do not use a malfunctioning or damaged
power supply!
• This model must only be operated with
one power source per circuit!
• This product is not a toy, not suitable for
personnel under 14 years of age. This
product has small parts, sharp parts, and
moving parts.
• This model must only be operated with a
safety-assured power supply with the
identification!
• The power supply is not a toy!
• Disconnect the model from the power
supply before cleaning or servicing!
• Do not insert the track power connecting
wires into household "mains" voltage
outlets.
5
Publicité
