Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Saw Blades for KGS 216:
E TCT Saw Blade
216 x 2,4 x 1,8, 30 24 alternate bev-
el teeth
For rip and cross cuts in solid wood.
F TCT Saw Blade
216 x 2,4 x 1,8, 30 48 alternate bev-
el teeth
For rip and cross cuts in solid wood
and particle board.
G TCT Saw Blade
216 x 2,4 x 1,8, 30 60 trapezoidal
flat teeth
For rip and cross cuts in faced and
veneered sheets.
Saw Blades for KGS 254:
H TCT Saw Blade
254 × 2.4 / 1.8 × 30 24 W
For rip and cross cuts in wood and
uncoated particle board.
I
TCT Saw Blade
254 × 2.4 / 1.8 × 30 48 W
For rip and cross cuts in wood and
panels.
J TCT Saw Blade
254 × 2.4 / 1.8 × 30 60 W
For rip and cross cuts in solid wood,
panels and thick-walled plastic ex-
trusions.
K TCT Saw Blade
254 × 2.4 / 1.8 × 30 80 FT
For rip and cross cuts in wood, pan-
els, cable ducts, high-quality ve-
neered panels and laminate.
12. Repairs
A
Danger!
Repairs to power tools may only be car-
ried out by qualified electricians!
Electric tools in need of repair can be
sent to the Service Centre of your
country. The address can be found in
the Spare parts list.
Please attach a description of the fault
to the electric tool.
30
13. Environmental Consider-
ations
The machine's packing can be 100%
recycled.
End-of-life power tools and accessories
contain large amounts of valuable raw
materials and plastics which must be
recycled.
This manual was printed on chlorine-
free bleached paper.
14. Trouble Shooting
This section describes problems and
malfunctions which you should be able
to resolve yourself. If the measures de-
scribed here do not solve your problem,
see under "Repairs".
A
Danger!
Many accidents happen particularly in
connection with problems and faults.
Therefore please note:
Always unplug before servicing.
Check that all safety devices are
operational again after each fault
service.
Motor does not run
No mains voltage
check cables, plug, outlet and
mains fuse.
No crosscut function
Transport locking pin engaged:
Pull transport locking pin out.
Safety lock engaged:
Release safety lock.
Only little sawing performance
Saw blade blunt (possibly tempering
marks on blade body):
Saw blade not suitable for material be-
ing cut (see chapter "Technical Specifi-
cations");
Saw blade warped:
Replace saw blade (see chapter
"Maintenance").
Saw vibrates heavily
Saw blade warped:
Replace saw blade (see chapter
"Maintenance").
Saw blade incorrectly mounted:
Mount saw blade correctly (see
chapter "Maintenance").
Stiffness of rotating table
Saw dust build-up under rotating table:
Remove saw dust.
15. EC Declaration of Con-
formity
We hereby declare that the product
specified below conforms to the rele-
vant basic safety and health require-
ments of the EC directives based on its
design and type as well as in the ver-
sion distributed by us. Any unauthor-
ised product modification will invalidate
this declaration.
Product:
Crosscut and mitre
saw
Type:
KGS 216, KGS 254
EC directives
applied:
– to 28.12.2009:
98/37/EC
– from 29.12.2009:
2006/42/EC
2006/95/EC
2006/108/EC
Harmonised stand-
EN 61029-1
ards applied:
EN 61029-2-9
EN 55014-1 (2006)
EN 61000-3-2
(2006)
EN 61000-3-3
(1995)+A1+A2
Erhard Krauss
Technical Director / COO
Meppen, Germany 10.01.2009
Metabowerke GmbH
Werk Meppen
Daimlerstraße 1
49716 Meppen,
Germany
Publicité
