Toto TLP02201 Manuel D'installation page 6

EN
Before Installation
z If the water supply pressure exceeds 1.0 MPa, reduce the pressure to about 0.1 - 0.5 MPa
using a commercially available pressure reducing valve.
We recommend a water supply pressure of about 0.1 - 0.5 MPa for comfortable use of
the faucet.
z In order to prevent scalding due to erroneous operation, be sure to set the cold water
supply pressure higher than the hot water supply pressure or set them to the same
pressure.
Even when applying pressure to the hot water side, be sure to set the hot water supply
pressure side lower than the cold water side.
z Connect the hot-water supply pipe at a minimum length from the water heater in
order to reduce resistance and be sure to wrap the water supply pipe with thermal
insolation.
z Since the flow is examined before packaging the product, some water may remain in
the product, but nothing is wrong with the product.
z In order to make it easier to adjust the water pressure and check the equipment', be
sure to separately prepare a water shutoff valve, a cold-water supply hose and a hot-
water hose.
Cleaning the cold-/hot-water supply pipes before mounting the product
Before mounting the product
Prepare a commercially available flexible hose, etc. and a bucket, connect the flexible
hose to the cold-/hot-water supply pipes and flush out debris and sand in the cold-/hot-
water supply pipes.
If you do not clean the inside of the cold-/hot-water supply pipes, debris,
sand, etc. in the pipes may get caught in the valve and cause the following
phenomenon.
(1) Little water volume is discharged.
(2) Water does not stop
Connection of the hoses
4
(1) Put the packing in the cap nut of the cold-/hot-water hoses, and screw the
hose into the valve body and the water shutoff valve to anchor it.
(2) Put the packing in the cap nut of the connecting pipe, and screw the
connecting pipe into the hose joint to anchor it. Put the packing in the cap nut
of the connecting hose of the hose joint and screw the connecting hose into
the valve body to anchor it.
z Make sure that the packing is mounted.
z Pay attention not to bend the connecting hose and cold-water hose
with more force than necessary or pull them with undue force.
Connect the Pop-up waste
5 (1) Remove the water drainage lid, the flange and the (two) atypical packings
from the water drainage metal fitting body.
(2) Pass the flange with the atypical packings through the upper side of the water
drainage port of the wash bowl.
(3) Tighten the the water drainage metal fitting with the atypical packings to the
flange from the bottom of the wash bowl.
z Carry out the mounting work paying attention to the direction of
the atypical packings.
z Apply joint sealant.
(4) Tighten the kick lever box in the direction of the water faucet paying attention
not to damage the wash bowl.
(5) Insert the pulling bar into the guide from below the spout body.
(6) Mount the pushbutton, screw and the lid on the pulling bar in this order.
(7) Install the cap nut and the anchoring metal onto the kick lever from faucet
side. Install the washer onto the kick lever from the drainage side.
(8) Pass the pulling bar through the anchoring metal fitting, then pass the kick
lever through the kick lever box and anchor it with the cap nut.
(Connect the water drainpipe [procured in the field].)
Mounting of the spout
1 (1) Remove dirt around the mounting holes.
(2) Pass the spout through the (small) packing, insert the spout into the counter
from above, and screw in the (large) packing, the spring washer and the
mounting nut to anchor the spout.
Anchor the spout so that it comes to the center of the mounting hole.
Anchoring the valve body
2 (1) Mount the body mounting nut, washer and packing in this order on the product
body.
Screw in the body mounting nut down to the lowest thread.
(2) Insert the body from under the counter and screw in the mounting metal fitting
until it touches the body.
(3) Press the 2 screws of the body mounting nut strongly against the washer.
z Be sure to mount the hot-water supply valve body (Label H) on the
left side of the spout and mount the cold water supply valve body
(Label C) on the right side of the spout.
z Mount the valve body in the center so that it does not deviate from
the mounting hole.
How to mount the handle
3 Insert the handle into the valve body and anchor it with the setscrew incorporated
in the handle.
*Set it so that the setscrew comes to the backside.
z Mount the handle so that C/H comes to the positions shown in the
figure when the index of the handle shows the water off.
z Mount the handle so that it comes to the position in the figure when
the handle is operated.
*The handle position can be fine-adjusted by replacing the adjusting
bush.
(9) Make sure that the water drainage lid is open when the kick lever is lowered to
the lowest position.
*If the opening of the water drainage lid is small, draining time may take more
time than usual to drain.
z If this opening is small, turn the shaft of the water drainage lid to
adjust the height, and anchor it with the nut.
z If the kick lever and the pulling bar interfere with the wall and the
water drain pipe cut them to a length that they do not interfere.
(10) Adjust the clearance between the spout and the pushbutton to 5 - 10 mm
with the kick lever lowered to the lowest position and anchor the kick lever
and the pulling bar with the screw of the anchoring metal fitting.
Checking after installation
6 z Open the main valve of the piping and make sure that the water comes out
from the spout.
z Check the connections for water leaks.
*If supply water pressure is high and handle operation is heavy, please adjust the
flow rate by stop valve without being too small.
(Handle operation will be lighter.)
How to clean the filter
7 Be sure to clean the filter after mounting.
If the filter is clogged, the flowrate decreases and only cold water or scalding hot
water comes out, thus the product does not fulfill its purpose. Explain things to
the customer and recommend cleaning from time to time.
How to check for looseness
Check the handle, spout and water drain metal fitting for any looseness.
Specifications
Operating pressure range
Recommended Operating pressure
Test pressure
Hot water temperature
Recommended hot water temperature :
Flowrate under 0.3 MPa
6
Water flow and water leaks
: Max 1.0 MPa
: Min 0.05 MPa
: 0.1 - 0.5 MPa
: 1.6 MPa
: Max. 80 °C
60 °C
: approx 5.0 L/min