EINHELL FREELEXO SMART Instructions D'origine page 42

notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6. Operation
6.1 Main switch
The robot lawn mower is equipped with a main
switch (7). Use the main switch (7) to switch the
robot lawn mower on (ON) and off (OFF) (Fig. 8).
Once the robot lawn mower has been switched
on, it is locked by a PIN.
6.2 Control panel
The robot lawn mower has already been pro-
grammed at the factory and default settings have
been made for it. However, these can be changed
if required. Even though the factory settings will
be suitable for most gardens, you should still
familiarize yourself with the available options ne-
vertheless.
Explanation of the control panel with LCD
(Fig. 9a)
50. LCD
51. "SET" button
52. "MODE" button
53. "START" button
54. "BACK" button
55. Navigation buttons
56. "OK" button
Explanation of the symbols on the LCD
(see Fig. 9b):
60. Signal strength of the network connection
61. Signal detection of the perimeter wire
62. Rain sensor status
63. Battery status
64. Manual mowing
65. Time schedule control
66. SMART control
67. Back to the charging station
6.3 Cutting height adjustment facility
Important! Adjust the cutting height only when
the robot lawn mower has been switched off . Do
this by pressing the STOP button (3). The cutting
height adjustment facility (4) allows the cutting
height of the robot lawn mower to be set to infi ni-
tely adjustable settings between 20 and 60 mm,
which can be viewed on the scale.
If the grass is taller than 60 mm it has to be shor-
tened to a maximum of 60 mm fi rst to avoid expo-
sing the robot lawn mower to excessive load and
Anl_FREELEXO_SMART_SPK13.indb 42 Anl_FREELEXO_SMART_SPK13.indb 42
GB
adversely aff ecting its operating effi ciency. Use a
conventional lawn mower or trimmer to do this.
After installation has been completed, the cutting
height can be adjusted using the cutting height
adjustment facility (4). Always start with a higher
cutting height and reduce it in small steps until
you reach the desired height.
6.4 Locking mechanism / PIN
The locking mechanism prevents the unautho-
rized use of the robot lawn mower without a valid
code. You have to enter a personal four-digit secu-
rity code for this.
Lock release
Before you start using the robot lawn mower, you
have to enter the correct PIN (standard PIN: "0-0-
0-0"). Enter the PIN with the help of the navigation
buttons (55).
Standard PIN: New PIN:
0 0 0 0 _ _ _ _
Changing the PIN
To change the PIN, proceed as follows.
1. Unlock the control panel.
2. First press the "SET" button (51) in order to
make your settings.
3. Use the navigation buttons (55) to navigate in
the menu on the LCD (50) to the point "Gene-
ral information" and then „PIN code".
4. First enter the current PIN (standard PIN 0-0-
0-0) with the help of the navigation buttons
(55).
5. Then use the navigation buttons (55) to enter
your personal PIN.
6. Confi rm the settings you have just made.
7. Repeat step 5. and step 6 in order to confi rm
the new PIN.
8. Important! Make a note of the new PIN.
Requesting your PIN if you lose it
Have the receipt and the serial number of the
robot lawn mower ready. You need them in order
to get your PIN.
Version A:
1. Press and hold the „SET" button (51) for 6
seconds in locked status.
2. The PUK will now appear in the display (50).
3. Contact the customer services team to obtain
your PIN.
- 42 -
26.09.2023 13:52:34 26.09.2023 13:52:34