EINHELL FREELEXO SMART Instructions D'origine page 47

lawn mower more often.
•
Shorten the lawn only in small steps in order
to prevent heavy soiling.
•
There are no other parts inside the equipment
which require maintenance.
7.2.1 Replacing the blades
Only replace the blades with genuine blades, as
this will ensure top performance and safety.
The robot lawn mower is equipped with three bla-
des (10) fi tted to a blade plate (11). These blades
(10) have a service life of up to 3 months (if they
do not strike any obstacles). Please replace all
three blades (10) at the same time to ensure that
there is no possibility of any impairment to the
effi ciency and balance of your equipment.
To change the blades (10), proceed as follows
(Fig. 12) - Caution! - Wear work gloves:
1. Use a screwdriver to block the rotation of
the blade plate (11). Do this by inserting the
screwdriver through the holes in the blade
plate (11) and the protective ridge.
2. Undo the fastening screws
3. Remove the blades (10) and replace them
with new ones. Always replace all three bla-
des (10) as a set.
4. Then retighten the fastening screw. Check
that the new blades (10) are able to rotate
freely.
Perform a general inspection of the robot lawn
mower at regular intervals and remove any depo-
sits which may have accumulated. At the start of
each season, ensure that you check the condition
of the blades (10). If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.
7.2.2 Software update
If you want to update the software, copy the new
software to an empty USB stick (format the USB
stick fi rst if necessary). Make sure that the rechar-
geable battery is fully charged before you carry
out the following steps.
1. Place the robot lawn mower in the area to be
mowed. The robot lawn mower must not be
in the charging station during the software
update.
2. Connect a USB stick to the USB connection
as shown in the illustration. (Fig. 11).
3. Switch on the main switch (7) (ON).
4. The robot lawn mower will now start updating
the software and will display the current sta-
tus.
5. Pull out the USB stick and restart the robot
Anl_FREELEXO_SMART_SPK13.indb 47 Anl_FREELEXO_SMART_SPK13.indb 47
GB
lawn mower with the main switch (7).
7.2.3 Repairing the perimeter wire
If the perimeter wire (18) gets severed at any
point, use the supplied cable connectors (16) to
repair it. To do so, insert both ends of the severed
perimeter wire (18) into the cable connector (16)
and squeeze it together with the help of a pair of
pliers. Connect the power plug to the socket out-
let. Then check whether it is working properly by
checking the LED indicator (21) on the charging
station (19).
7.3 Ordering spare parts
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Replacement blades Art. No.: 34.140.20
8. Storage
Fully charge up the rechargeable battery before
putting it into storage over winter and switch
off the robot lawn mower at the main switch (7)
(OFF). Take the rechargeable battery out of the
equipment. Disconnect the power supply unit (13)
from the power supply and the charging station
(19).
The perimeter wire (18) can be left outdoors over
winter. However, make sure that the connections
are protected against corrosion. To do so, discon-
nect the connections of the perimeter wire (18)
from the charging station (19).
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30°C. Store the equipment
in its original packaging.
- 47 -
26.09.2023 13:52:36 26.09.2023 13:52:36