Nemox Gelato 5KSc Mode D'emploi page 8

the button (11), you will be able to select other
programs in sequence.
•When the LED becomes steadily lit, the
associated program starts up and begins the
production cycle.
•The machine has 4 production programs and
4 preservation cycles for each of them. When
the program selected starts up you can
choose the preservation cycle desired. Chose
the preservation cycle by pressing the button
(12) repeatedly. When switching from the first
preservation program to the fourth, gelato
consistency increases gradually.
•When the ice cream reaches the right
consistency, the production program stops
automatically and the preset preservation
cycle is enabled.
•Every production program has a preset
threshold time after which the machine enters
in preservation cycle, regardless of the current
production phase.
•If deemed appropriate, it is possible to enable
the selected preservation cycle at any time ,
ending the production program. Select the
preservation cycle desired via the key 12
(sequence selection). Keep the paddle button
(2) an compressor button (1) pressed
simultaneously for 3 seconds. The machine
will immediately switch from production cycle
to preservation cycle.
•CLASSIC ITALIAN GELATO AND SORBET
PROGRAM. By pressing button (11) once, the
LED (11a) will light up and activate the
production program. At the end of the
production cycle, the LED (11a) flashes
indicating that the selected preservation cycle
has been activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
l o c k s . T h e p r e s e r v a t i o n f u n c t i o n i s
automatically activated.
• SEMI-SOFT GELATO PROGRAM
button (11) twice, LED (11b) will light up and
activate the processing program. At the end of
the production cycle, the LED (11b) flashes
indicating that the selected preservation cycle
has been activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
l o c k s . T h e p r e s e r v a t i o n f u n c t i o n i s
automatically activated.
• GRANITA PROGRAM
8
. By pressing
. By pressing button (11)
English
three times causes LED (11c) to light up and
activate Granita processing. At the end of the
production cycle, the LED (11c) flashes
indicating that the selected preservation cycle
has been activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
l o c k s . T h e p r e s e r v a t i o n f u n c t i o n i s
automatically activated.
• FAST COOLING PROGRAM.
(11) four times causes LED (11d) to light up
and activate the fast cooling program. At the
end of the production cycle, the LED (11d)
f l a s h e s i n d i c a t i n g t h a t t h e s e l e c t e d
preservation cycle has been activated.
This program is used when processing
mixtures with high initial temperatures. The
program quickly brings down the temperature
without adding too much air into the mixture,
saving time and improving the quality of the
ice cream made.
SELECTED PROGRAM VARIATION
Should it become necessary to select a
different program when a program is running,
you can simply press button (11). When the new
program is selected, the currently running
program will stop. The new program will be
active immediately with its own execution times
that will restart from the initial values.
SWITCHING FROM AUTOMATIC TO MANUAL
OPERATION
During the processing program, it is possible to
switch to manual mode at any time.
Holding down button (11) for 3 seconds
switches the machine to manual mode while
enabling the paddle LEDs (2a) and compressor
(1a).
The preservation cycle selected will be
deactivated.
TURNING OFF THE MACHINE DURING
AUTOMATIC OPERATION MODE
If you need to turn off the machine before the
completion of the active processing program,
you first need to switch to manual mode by
pressing and holding button (11) for 3 seconds
and then pressing paddle (2) and compressor
(1) to stop any activity. Do not act directly on the
main switch (10)!
PRESERVATION CYCLE VARIATION WHILE A
PROGRAM IS RUNNING
During the preparation phase it is possible to
Pressing button