Briggs & Stratton 550 Serie Mode D'emploi page 9

How To Change The Gear Reduction Oil - Figure 11
If your engine is equipped with a gear reduction unit, service as follows.
1. Remove the oil fill plug (B) and the oil level plug (C).
2. Remove the oil drain plug (A, Figure 11) and drain the oil into an appropriate
receptacle.
3. Install and tighten the oil drain plug.
4. To refill, slowly pour gear lube into the oil fill hole (see Specifications section).
Continue to pour until the oil runs out of the oil level hole.
5. Install and tighten the oil level plug.
6. Install and tighten the oil fill plug.
Important: The oil fill plug has a vent hole (D) and must be installed on the top of the
gear case cover as shown.
How To Clean The Air Cooling System - Figure 12
WARNING
Running engines produce heat. Engine parts, especially muffler,
become extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
Allow muffler, engine cylinder and fins to cool before touching.

Remove accumulated debris from muffler area and cylinder area.

NOTICE: Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
Use a brush or dry cloth to remove debris from the finger guard (A) (Figure 12). Keep
linkage, springs and controls (B) clean. Keep the area around and behind the muffler (C)
free of any combustible debris.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Fuel Or Equipment With Fuel In Tank
Store away from furnaces, stoves, water heaters or other appliances that have

pilot light or other ignition source because they can ignite fuel vapors.
Fuel System
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum
deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh,
use Briggs & Stratton Advanced Formula Fuel Treatment & Stabilizer, available
wherever Briggs & Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine if a fuel stabilizer is added according
to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel
system before storage.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil.
Troubleshooting
Need Assistance? Go to BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in
USA).
en
Specifications
Engine Specifications
Model
Displacement
Bore
Stroke
Engine Oil Capacity
Gear Reduction Specifications (if equipped)
Gear Reduction Oil Type
Gear Reduction Oil Capacity
Tune-up Specifications *
Model
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
* Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10 F (5.6 C) above 77 F (25 C). The engine will operate satisfactorily at
an angle up to 15. Refer to the equipment operator's manual for safe allowable
operating limits on slopes.
Common Service Parts n
Service Part
Standard Air Filter
High Capacity Air Filter
Advanced Formula Fuel Treatment &
Stabilizer
Spark Plug
Spark Plug Wrench
Spark Tester
n We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
83100
7.74 ci (127 cc)
2.441 in (62 mm)
1.654 in (42 mm)
18 -- 20 oz (0.54 -- 0.59 L)
80W-90
4 oz (0.12 L)
83100
0.030 in (0.76 mm)
180 lb-in (20 Nm)
0.006 - 0.010 in (0.15 - 0.25 mm)
0.005 - 0.007 in (0.13 - 0.18 mm)
0.005 - 0.007 in (0.13 - 0.18 mm)
Part Number
797258
796970
5442
797235
89838, 5023
19368
9