Télécharger Imprimer la page

Pioneer GR-777 Mode D'emploi page 8

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
PANEL AND REMOTE CONTROL UNIT FACILITIES
@) SET L & R switch (and indicator)
When
this switch is on, you can use the control switches of either
channel to provide simultaneous adjustment of both channels. (The
indicator lights when this is on.)
NOTE:
This does not make both sides have the same settings, it only lets you
adjust the same frequency band on the left and right channels at the
same time.
(2 EQUALIZER switch
Turn this switch on to apply equalization to the sound. Turn it off when
you do not want equalization.
(3) FLAT switch
Press this switch to reset all frequency bands to their center ''0"'
positions.
@4 PRESET/PROGRAM
switch
This selects PRESET or PROGRAM
operation for the five ''memory
recall'
switches,
as
confirmed
by the
PRESET
and
PROGRAM
indicators.
(The five ''memory recall' switches can be used to recall the factory
preset curves or your own programmed curves.)
G5) REV (Reverse) switch
This inverts the current equalization curve, so the boosted frequencies
are reduced and the reduced frequencies boosted.
Control switches
Press the plus side to boost the level; press the minus side to reduce it.
NOTE:
Tweeters may be damaged if you boost the high frequencies exces-
sively and then play music at high volume. Keep the amplifier volume
at a suitable level when using equalization curves that emphasize the
treble tones.
@) SPECTRUM
ANALYZER/EQUALIZER display
When operating as a spectrum analyzer, this shows the effect of your
equalization upon the actual output signal.
When operating as a graphic equalizer display, it shows the equaliza-
tion curve.
Memory recall switches/indicators
There are five memory switches A through E. When the PRESET indi-
cator is lit, these select the factory presets:
HEAVY: a powerful, heavy bass sound.
CLEAR: a bright, clear sound.
SOFT: a soft sound, free from harshness.
VISUAL: useful with video soundtracks and TV.
VOCAL: adds presence to vocals.
When the PROGRAM indicator is lit, these switches select the equali-
zation curves that you have stored.
PRESET and PROGRAM indicators
These indicate whether you have selected the PRESET or the PROGRAM
equalization curves.
EQUALIZER indicator
This lights when the EQUALIZER switch is on.
@) MONITOR indicator
This lights when the TAPE MONITOR switch is on.
@ MEMORY switch/indicator
Use when storing equalization curves in the memory recall switches.
@) Level meter
Shows signal level.
8
<ARE1098>
REMOTE
SENSOR window
Point top of remote control unit at this window during operation.
NOTE:
When making connections between CONTROL IN/OUT terminals for ex-
tended remote control, other components bearing the Fal mark may be
inserted between the component and the equalizer. However, the equal-
izer has only a CONTROL OUT terminal, so it should be at the end of the
chain.
r .
e
SONTROW
INPUT
BS aap)
OUTPUT
©
Co
Ve,
CONTROL
iN
|
Other component
Other component
with the SRI mark.
with the SRI mark.
REMOTE CONTROL UNIT FACILITIES
@) EQUALIZER
OFF/ON key
Same as front panel EQUALIZER switch.
@6) Contro! keys
Same as equalizer control switches on front panel.
@) MEMORY
CALL function keys
e A — E keys: same as memory
recall switches on front panel.
¢ PRESET/PROGRAM
key: same as front panel PRESET/PROGRAM
switch.
Range of remote control
When the remote control unit is pointed at the remote control sensor
window on the deck amplifier and any of its keys is pressed, the unit
and other components can be operated by remote contol.
Distance: Within a range of about 7 meters from the unit's remote
control sensor window.
Angle: Within approx. 30 degrees from the center of the unit's remote
control sensor window.
Remote control will not be possible if there is an obstacle between the
remote control unit itself and the unit's remote sensor window.

Publicité

loading